Find the toughness (or energy to cause fracture) for a metal that experiences both elastic and plastic deformation. Assume Equation 6.5 for elastic deformation, that the modulus of elasticity is 172 GPa (25 x 106 psi), and that elastic deformation terminates at a strain of 0.008. For plastic deformation, assume that the relationship between stress and strain is described by Equation 6.19, in which the values for K and n are 6900 MPa (1 x 106 psi) and 0.25, respectively. Furthermore, plastic deformation occurs between strain values of 0.008 and 0.61, at which point fracture occurs.

Find the toughness (or energy to cause fracture) for a metal that experiences both elastic and plastic deformation. Assume Equation 6.5 for elastic deformation, that the modulus of elasticity is 172 GPa (25 x 106 psi), and that elastic deformation terminates at a strain of 0.008. For plastic deformation, assume that the relationship between stress and strain is described by Equation 6.19, in which the values for K and n are 6900 MPa (1 x 106 psi) and 0.25, respectively. Furthermore, plastic deformation occurs between strain values of 0.008 and 0.61, at which point fracture occurs.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A cylindrical metal wire 2m long is loaded in tension, causing it to extend 15mm. Calculate the axial strain and represent you answer in terms of microstrain and % elongation. ● ● Draw a free body diagram (geometry & forces) Identify stress plane Calculate microstrain and % elongation and write it (with appropriate units) in the outlined box b) Based on your calculation, is this behavior typical of a ductile or brittle material? Check one box.
3. A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A force of 3370 Ibr produces a reduction in specimen diameter of 7 x 103 mm. Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. 4. A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and final diameters are 20.000 and 20.025 mm, respectively, and its final length is 74.96 mm, compute its original length if the deformation is totally elastic. The elastic and shear moduli for this alloy are 105 GPa and 39.7 GPa, respectively.
2. Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its elongation when a load of 300 N is applied. Assume that the deformation is totally elastic. 3. A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A force of 3370 Ibr produces a reduction in specimen diameter of 7 x 10* mm. Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. 4. A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and final diameters are 20.000 and 20.025 mm, respectively, and its final length is 74.96 mm, compute its original length if the deformation is totally elastic. The elastic and shear moduli for this alloy are 105 GPa and 39.7 GPa, respectively.
A 3-mm-long gold alloy wire intended to electricallybond a computer chip to its package has an initial diameter of30 μm. During testing, it is pulled axially with a load of 15grams-force. If the wire diameter decreases uniformly to29 μm, compute the following:a. The final length of the wire.b. The true stress and true strain at this load.c. The engineering stress and strain at this load.
During stress-strain test, the unit deformation at a stress of 35 MPa was observed to be 167 x 10^-6 m/m and at a stress of 140 MPa it was 667 x 10^-6. If the proportional limit was 200 MPa, what is the modulus of Elasticity (GPa)? What is the strain corresponding to a stress of 80 MPa?
You compress a cylindrical biological sample with an engineering stress of -1 MPa. The sample is made of an isotropic elastic material with Young's modulus of E = 10 MPa and Poisson's ratio v = 0.3.(a) Calculate the engineering strains in the direction where the stress is applied and the transverse direction.(b) How much elastic strain energy is present in the deformed sample if it has a volume of 10 cm3?(c) The material has a hysteresis of 0.1. How much energy will you be able to recover when the sample is relaxed?(d) Calculate the true stress and true strain in the compressed sample.
A steel specimen 12mm diameter has gauge length 50mm. the steel specimen had tested via tensile test under maximum load 66KN with elongation 7.5mm, and the yield load of this specimen is 15KN with elongation 2.4mm. Calculate: 1- The engineering ultimate stress (ultimate tensile strength), and engineering strain at this point. 2- The engineering stress and strain at yield point. 3- The modulus of elasticity, and the modulus of resilience. 4- The final or fracture strain of a steel specimen, if you know that the final length of specimen after testing is 58.5mm. 5- The true stress and strain for ultimate point. any four point sir
A 3-mm-long gold alloy wire intended to electrically bond a computer chip to its package has an initial diameter of 30 µm. During testing, it is pulled axially with a load of 15 grams-force. If the wire diameter decreases uniformly to 29 µm, compute the following: (a) The final length of the wire. (b) The true stress and true strain at this load. (c) The engineering stress and strain at this load.
The Young's modulus of a material is 125 GPa and Poisson's ratio is 0.25. The modulus of rigidity of the material is
(A A\ Find the toughness for a metal that experiences both elastic and plastic deformation. The modulus of elasticity is (15 x 10 psi), and that elastic deformation terminates at a strain of (0.007). For plastie deformation the values for K and n are (221,000 psi) and (0.15), respectively. Furthermore, plastic deformation occurs between strain values of (0.007) and (0.60). إضافة ملف
A cube has sides that are initially 80 mm and is subjected to stresses of 40 MPa (tensile), 30 MPa (compressive) and 70 MPa (tensile) in the x, y and z -directions, respectively. Calculate (a) the strains in these directions, (b) the changes in dimensions, (c) the volumetric strain and (d) the change in volume.Take E = 214 GPA and Poisson’s ratio = 0.33.
A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by auniaxial tensile load of 4800 N in 120 seconds. At this load, the length of therod is measured as 49,2 mm. Calculate the followings:(a) Stress and strain occurred on the rod at this load.(b) Initial strain rate.(c) Diameter of the rod at this load.(Yield strength : 380 MPa, Ultimate Tensile Strength: 670 MPa,Modulus of Elasticity: 210000 MPa were given for this material)