Find the source voltage Vs. the apparent power, complex power, average power, reactive power, and power factor from the source. What is the capacitance to be connected in paralle with the load to increase the power factor to 95%? 0.05 Ω jO.20 20 kW + Vs 240/0° V rms 0.7 leading 12 kVA 0.9 lagging

Find the source voltage Vs. the apparent power, complex power, average power, reactive power, and power factor from the source. What is the capacitance to be connected in paralle with the load to increase the power factor to 95%? 0.05 Ω jO.20 20 kW + Vs 240/0° V rms 0.7 leading 12 kVA 0.9 lagging

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A sinusoidal voltage is applied to a single phase load. The input current wave form is as shown…

A: Phaser diagram is given, From the diagram, vm=1202 V RMS voltage is given by, Vr=Vm2=12022=120 V

Q: What is the power factor of a load with complex power S = 1000 + j250 KVA? what kind of load is it?…

Q: Find power factor of given circuit 30/0° V rms -j22 42

A: Power factor is the ratio of true power by apparent power. The value of power factor lies in between…

Q: The instantaneous current of AC source is 1, inst Select one: Oa. 250 A b. 176.6 A OC. 300 A Od. 150…

Q: For the circuit in the figure below, determine the load impedance that maximizes the average power…

Q: The power factor across a load is 0.57 lag. The real power across the load is 375 W. Voltage applied…

A: A system which have power factor across a load is 0.57 lag. The real power across the load is 375 W.…

Q: The power triangle shown represents the characteristics of a 230 V 60 Hz ac motor. How much…

A: Add a capacitive reactive power to counteract the existing inductive reactive power.The formula to…

Q: i(t) Find rms value of given current waveform. HAA 10 2 4 6 8 10 -10

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: Is |L 20020°V, L Vs rms S. - In the circuit in the figure; • L1 load draws 15 kVA with lagging power…

A: complex power S =Scos(angle)+ S sin(angle) where S is KVA and angle is power factor angle

Q: If a Load absorbs an average power of 8 kW at a leading power factor of 0.8, Then the complex power…

A: Active power P= 8kW Power factor = 0.8 leading Complex power S?

Q: Consider a step down converter with a resistive load. It is supplied by a DC power source of…

Q: A Z load draws 12kVA from a 120 V-rms sinusoidal source with a back power factor of 0.85. Find the…

Q: A factory draws an apparent power of 300 kVA at a p.f. of 0-65 lagging. What is the reactive power…

Q: The source voltage in the circuit is 100cos5000t V (rms). The load impedance (ZL) connected is…

A: Assume a voltage of 1 V at the output terminals. Draw the circuit diagram.

Q: A V sine The supply voltage V = 120230° volt. Load A is 4 KVA at power factor 0.8 leading. Load C is…

Q: A non-sinusoidal voltage (e=20+15sin1000t+ 10sin3000t+5sin4000t) Volt is plied to the circuit shown.…

A: A Non- Sinusoidal Voltage; e=20+15sin1000t+10sin3000t+5sin4000tTo find the total power=?Power=V2Z

Q: A Z load draws 10kVA from a 120 V-rms sinusoidal source with a back power factor of 0.8. Find the…

A: Given that Although fromula of real power or average power is given by

Q: 62 Find power factor of given circuit ww- 30/0° V rms

Q: Compute for the value of the impedance load that will absorb a maximum average power. 10Ω j15 N ell…

A: To absorb maximum average power first we have to calculate Thevenin's impedance across the load by…

Q: A ful-wave reebifel Ginasen Rad volitnge is clipped at of ik mayimum valye . Calculate the ayerage…

Q: The average Power to the Plont Shown in Figure is 2438 kW and Power factor is 0:707 (99ging. The…

A: In the question A power plant Have average power P= 2438kW at 0.707 PF lagging. Frequency w= 377…

Q: the RMS value of the current is? /2) the peak value of the voltage is?/3) the value of the reactive…

Q: i(1) A Find rms value of given current waveform. 10 2 4. 6 8 10 -10

A: In this question, we have to find the rms value of given current waveform,The waveform is given as

Q: S. 20020°V L ms In the circuit in the figure; • L1 load draws 15 kVA with lagging power factor 0.6.…

A: From the complex power

Q: Problem 7: Compute the complex power S in polar form, drawn by a certain load if it is known that a.…

A: Use basic formulas of power triangle

Q: 30 kW 240/0° V rms (t 0.75 lagging (+1)

Q: Draw the power triangle associated with the source, 300230° Vrms. illustrate the apparent, active,…

A: We need to draw the power triangle and calculate the power factor for the given circuit.

Q: From the figure, find the average power (Average power) supplied to the elements. When the current…

Q: Silicon diodes 10 V 2.7 V Design -10 V -17.3 V

Q: What is the capacitance to be connected in parallel with the load to increase the power factor to…

Q: A Load absorbs 10 kVA at a lagging power factor of 0.6. The complex power is: Select one: a. 2000+…

A: The correct solution is given below

Q: If a Load absorbs an average power of 8 kW at a lagging power factor of 0.8, then the complex Select…

A: Active power P= 8kW Power factor = 0.8 leading Complex power S?

Q: for the circuit shown in the figure below, find I, Vr and Vc, and the corresponding sinusoidal…

A: In this question we need to find a VR , Vc , I and average power.

Q: If a A-connected load has a balanced impedance ZA 94 -17° 2 and a voltage = Z VBC = 265 / 82° V rms,…

A: The 3-phase system,The impedence,The voltage,

Q: Correct the power factor seen by the voltage source in the following circuit so that it is better…

A: It is given that:

Q: For the component shown in figure, find the sinusoidal current i using phasors. i L 240 pµH v = 8…

Q: A Load absorbs an average power of 8 kW at a lagging power factor of 0.8, The complex power is:…

A: Given, Average power, P = 8kW Power factor, pf = 0.8 lagging We need to determine the complex power…

Q: Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average…

Q: A Va Vb b B N Z̟ = 30/45° Ve C

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Find the source voltage Vs. the apparent power, complex power, average power, reactive
power, and power factor from the source. What is the capacitance to be connected in parallel
with the load to increase the power factor to 95%?
www
0.05 Ω
j0.2 Ω
20 kW
0.7
leading
240/0° V rms
12 kVA
0.9
lagging
Vs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need it in 5 minutes please
For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Determine whether the power factor is leading or lagging. V = 300/30° V rms, I = 0.5/60° A rms The value of apparent power is The value of real power is The value of reactive power is The power factor is (Click to select) ✓ W. VA. VAR.
RMS Value of sinusoidal current is given by O a. Im//2 b. I,x2 Ос. c. ImX/2 O d. I/2 m
The e.m.f. 's from four generators are e = 4 7sin@t e = 2 cos ot, e =/7 cos(@t + 90° ) and 1 3 = 5/2 sin(ot – 90° ). The alternators are connected in series. e4 18. Find the rms value of the resultant e.m.f A 5.0 В 4.0 C 2.5 D None of the above. 19. If the resultant e mf is expressed in the form e = Asin(ot + B). Find Bin degrees. A 53.1 в 369 С -53.1 D -36.9
Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average power of 500 kW and a forward power factor of 0.9. Since the other load absorbs 400kw and 600kvar power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) Find the value of the capacitor to be connected parallel to the loads so that the power factor is 0.95 back d) Find and compare the magnitude of the current drawn from the .source for the situations before and after the capacitor is connected not: Please solve this question in detail, in a way that I can understand
A load is supplied by a 230 V, 50 Hz source. The active power P and the reactive power Q consumed by the load are such that 1 kW SPS2 kW and 1 KVAR SQS2 KVAR. A capacitor connected across the load for power factor correction generates 1 KVAR reactive power. The worst case power factor after power factor connection is Options: 1. 0.447 lag 2. 0.707 lag 3. 0.894 lag 4.1
Consider the circuit show in below figure 492 ww 200°V rms -j 20 The average power delivered by the source is (A) 37.85W, pf = 0.93 (Leading) (B) 75.7W, pf = 0.93 (Leading) (C)_75W,pf=0.93 (Lagging) (D) 37.85W, pf = 0.93 (Lagging) 6Ω
find The average power delivered to * .the circuit الحل بطريقة الممانعات وشكرا
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?
Two 660 V (rms) loads are connected in parallel. The two loads draw a total average power of 76.2 kW at a power factor of 0.8 leading. One of the loads draws 46 kVA at a power factor of 0.96 lagging
A load connected to a 210 V rms 50 Hz power lineIt draws 7 kW of power with a back power factor of 0.7.To make the power factor 0.8What should be the value of the capacitor to be connected parallel to the load?
i need the answer quickly