8) Please include complete solution and diagram if possible. To make a peg adjustment, the followingnotes were taken: the rod reading at Pwhen the wye level at 1 is 0.750 m while at2 is 1.906 m. The rod reading at Q when thewye level at 1 is 2.766 m while at 2 is 3.798m. Point 1 is on the line PQ and midwaybetween P and Q. Point 2 is on the sameline as P and 230 m from Q. With the wyelevel at point 2, find the rod reading at P (inm) for a level sight?

given- a wye level is used to take reading at point P and Q. to find- rod reading at P.

Answered: find the rod reading at P

Engineering

Civil Engineering

find the rod reading at P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The concrete slab supports the six vertical loads shown. Determine the x- and y-coordinates of the…

Q: Show complete solution and FBD. 3 decimal points The horizontal bar shown (Length = 18.0 feet)…

Q: Define about the Horizontal line load at the surface ?

A: Horizontal Line Load : 1. Line load which the load is the effect on line as the load on Railway and…

Q: Explain and provide examples for each of the following a) creeping- e.g. - b) falling- e.g.- c)…

A: a) Creeping- It is a slow ,gradual moment of soil which is loosened by water.The moment of soil is…

Q: The topic is all about Total Hydrostatic Force on Plane Surface. Show complete solution and…

A: Hydro-static Force: Hydro-static force is the total resultant force acting on a submerged body or…

Q: Compute the following: a. wall shear b. wall moment c. Deflection at mid-span

A: As per bartleby guidelines, only 1st question with 3 subparts need to be solved. So, for rest of…

Q: Determine the angle θ between the two cables attached to the pipe.

A: Consider the following diagram:

Q: 3. 2. 3. Draw I.L for R,, Vd left

A: The FBD of the beam is shown below:

Q: required to fail the san Pa. /hat was the angle of shearing resistance? 1.37 2.16 33.25

Q: Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force…

Q: 2-127. Determine the angle 0 between pipe segments BA and BC. B 3 ft 8 ft

Q: Consider the drawing below. What is the minimum coefficient of friction at E so that the truss is…

A: Coefficient of friction: The resistance of the moving body with respect to the surface is known as…

Q: 1. Using virtual work method, draw B.M.D for the shown structures (in case of beams, as well draw…

Q: is 35ksl. If Its aross-section is rectangular, determine its required thickness.

A: Take moment about A :∑ MA=0FBCsin608ft-2882=0FBC=8sin60FBC=9.2376kips

Q: Use Cantilever Method and determine (approximately) the

A: Cantilever Method is an Approximate Method used : Axial forces acting in column is directly…

Q: The gate AB shown in fig. 3 is rectangular and is 1.2m perpendicular to the paper. Compute the Force…

Q: Examine the diagram to the right. Calculate the tension in the rope. a) 5N b) ON ) 49.05 N c) 9.81 N…

A: Given data : The value of mass of block m=5 kg The value of acceleration due to gravity g=9.81 m/s2…

Q: dx Free Surface t dx Fixed ys dx Wall

A: a.) Applying the equilibrium condition in horizontal direction τdx×1=γ.sdx.sinθτ=γ.ssinθ But, the…

Q: 42 1OKN B. SKN 30 4m D 4m 6KN TRUSS C 2KN

Q: determine the allowable block shear strength (kN)

A: The values and diagram given in the question are as follows: Weld size=8 mm Using A572 Gr.50 steel

Q: Explain the Meyerhof and Hanna’s punching shear coefficient ?

A: Mayerhof and Hanna (1978) made more technically sound approach over their previous work from 1974 to…

Q: below, compute the magnitude of the force (F) required to break contact at point (c)?

A: From the given figure, the magnitude of F to break the contact point C has to be determined.

Q: 10 inch. 어4 inct 2. A horizontal force F of 15 lb is applied to the hammer shown. Assuming the…

Q: please show complete solution and fbd

A: Cable: - It is defined as flexible structures which are used to support transverse loads due to…

Q: The shown beam cross-section has f' 4,000 psi and f, 60,000 psi. Determine the depth of th neutral…

A: Given:- The compressive strength of the concrete = f'c = 4000 psi The yield strength of the steel =…

Q: Problem 1 b = 14 in %3D Determine the nominal flexural strength, Mn, of the rectangular section…

A: Flexural strength : Flexural strength is a material parameter defined as the stress in a material…

Q: a) What is the distance to centroid (x）? Please enter answer in mm and to 1dp. b) For the same…

Q: 2.) Determine the required spacing of vertical U-stirrups for a beam subject to axial tension. Given…

A: Stirrups are essentially accommodated holding the fundamental support of beam. It forestalls the…

Q: Q: A quarter circle gate AB of 1.5 m radius and 3 m wide, hinge at B, find the vertical force F…

A: horizontal pressure forceFx=wAxdistance of c.g. of the centroid of the gate from the free…

Q: 6ОKN 80KN 50KN 4m 2m 1m 3m W KN/m R1

A: Draw SFD and BMD We will first find reactions at support then draw SFD and BMD

Q: Curved panel BC in the figure is a 60° arc, perpendicular to the bottom at C. If the panel is 4 m…

Q: by assemb engineers can rotate in a vertical plane combined effect of gravity and a couple M od BC.…

A: Given:- mass=2.25kg of slender rodAB 1.85kg slender rod BC pin at B chord AC tension in chord…

Q: Determine the degree of indeterminacy of the structure below 02

Q: Q.4) A pipe assembly is acted on by four forces and one couple moment. The 300 N force is parallel…

Q: the horizontal bar shown (length = 15.0 feet) rests on smooth indines. compute the distance X at…

Q: 3.18 Solve for AC, BC, and BD using only one section cut. Use the right portion for the FBD.

A: A truss is a frame that is composed of a minimum of three sections joined by a pin or rigid joint.…

Q: 3.55 The concrete pier is subjected to soil pressure that causes the line loads shown. Determine the…

A: Converting the uniform varying loading into point load: Value of the load on horizontal component =…

Q: Q7: 1. Compare between tie and dowel bars

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: 4 EN/m 2m

A: Reaction at A and B in vertical direction is RA and RB respectively. Horizontal reaction at A is HA.…

Q: Draw the I L or and MB By B C 5m

A: To draw ild for By and MB

Q: gree of curve of 4° ar ute the degree of cur

A: solution of above problem is below:

Q: 4.) Draw shear and moment diagram. 15 kN/m 12kN/m 4m Add file 2m 6m

Q: construct the bar force or ettered bars. 6 at 25 ft 150 ft %3D

Q: Define In-Place Shear Tests—Vane Shear.

A: In-place shear tests refers to the test conducted on the site itself, to determine the shear…

Q: 6 kN/m 5) Redo problem # 4 taking support C as pin. 12 kN

A: Given Support C is PIN

Q: Calculate: a) depth of compression block, "a" b) fs

Q: Determine the minimum cross section controlled by shear. Ans.: b = _________ mm and d = _______ 2…

A: Shear force = Vu = 150KN f'c = 24MPa = 24000 KNm2

Q: 2. An architect wants to build a wall with the profile shown. To estimate the effects of wind loads,…

Concept explainers

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.

Question

8) Please include complete solution and diagram if possible.

To make a peg adjustment, the following
notes were taken: the rod reading at P
when the wye level at 1 is 0.750 m while at
2 is 1.906 m. The rod reading at Q when the
wye level at 1 is 2.766 m while at 2 is 3.798
m. Point 1 is on the line PQ and midway
between P and Q. Point 2 is on the same
line as P and 230 m from Q. With the wye
level at point 2, find the rod reading at P (in
m) for a level sight?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Fill in the blanks / identification: The weight of the suspended pipe in figure shown is 450 N. a. Determine the tensile force in BE a. 538.69 N c. 837.60 N b. 665.80 N d. 557.31 N b. Determine the tensile force in BD a. 538.69 N b. 665.80 N c. 837.60 N d. 557.31 N
Find div F and curl F if F(a, y, z) = 5y°z'i – 14x°2°j – 5xy'k. %3D | div F= curl F=
Ques-(3) If the fore bearing of line AB is 225º and the back bearing of line BC is 315º what is the included angle between AB and BC?
4. If line OC has an AZIM, Oof 83° 44' 19" and line OD has an AZIM, of 56° 21' 06", determine the angle of COD.
To make a peg adjustment, the following notes were taken: Wye level at 1 Wye level at 2Rod reading at P 0.75 1.906Rod reading at Q 2.766 3.798 Point 1 is on the line PQ and midway between P and Q.Point 2 is on the same line as P and Q but not between them. Point2 is 25 m from P and 230 m from Q. With the wye level at point 2,what is the rod reading at P for a level sight?
5. Determine the length and bearing of the omitted side. Unknown Bearlhg Unknown Distanoe N65 38'E 496.08 m S79 52'E 999:90 m N55 25'E 795.34 m $47 10'E 585.73 m
Section 0 1 2 Remark VR (m/s) Depth (m) (degrees) - - - Right bank. 1.75 55 1.8 1.84 57 2.5 2.00 60 3.5 e is the angle made by VR 4 2.28 64 3.8 with the boat direction 2.30 65 4.0 6 2.20 63 3.8 The various sections are 7 2.00 60 3.0 spaced at a constant 8 1.84 57 2.5 distance of 75 m apart 9 1.70 54 2.0 10 Left bank In the moving-boat method of discharge measurement the magnitude (VR) and direction.. () of the velocity of the stream relative to the moving boat are measured. The depth of the stream is also simultaneously recorded. Estimate the discharge in a river that gave the following moving-boat data. Assume the mean velocity in a vertical to be 0.95 times the surface velocity measured by the instrument. A) 3459.8 m3/s B 3485.9 m3/s с 3548.9 m3/s D 3458.9 m3/s
The bearing of line AB is N 48* W, and the bearing of line AC is N 35*15 E. The angle BAC is: A. 167*15' B.83*15 C. 96*45 D. 12*45
Answer: Max. safe V = 71.313 kph
To make a peg adjustment, the following notes were taken: Wye level at 1 Wye level at 2 Rod reading at P 1.226m 2.278m Rod reading at Q 1.598m 2.614m Point 1 is on the same line PQ and midway between P and Q. Point 2 is on the same line as P and Q but not between them. Point 2 is 23m from Q and Q is 220m from P. With the wye level at point 1, what is the rod reading (m) at P for a level sight? Round your answer to 3 decimal places.
Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s 4 ft - 1 attachment - 8 ft
If whole circle bearing of a line is 1200, its reduced bearing is A. S 20? E B. S 60? E C. N 120? E D.N 60? E. 1. The reduced bearing of a line is N 87? W. Its whole circle bearing is A. 87? B. 273.? C. 93? D. 3?.