Find the R ratio for this cyclic loading

Q: Calculate the normal force, shear force and moment at point C for the given problem below

A: For the given beam, it is required to determine the normal force, shear force and bending moment at…

Q: Q.4: A shaft subjected to tensile load has stress-strain curve is define by 125+185 01 find the…

A:

Q: Find the Shear Moment Diagram of the following problems using

A:

Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…

A:

Q: coefficient is n = 2. Press according to given Find the largest force P that it can apply.dimensions…

A:

Q: a. Estimate the torsional yield strength of the wire. b. Estimate the static load corresponding to…

A:

Q: Find the support reactions and joint force of the construction, shown on the figure, if 4-24 kN/m,…

A: Given data: q=24 kN/mM=25 kNmL= 3 m

Q: Link 2, shown in the figure, is 25 mm wide and 11 mm thick. It is made from low-carbon steel with…

A: Wide W = 25 mm Thickness t = 11 mm Sy = 165 MPaForce F = 80 KNFor  low-carbon steel E = 207GPa

Q: : The forces acting on gar-shaft be aring system are shown in the figxe given below. a) Calculate…

A: Given:-           The system of gear shaft bearing:                   The shaft is supported by the…

Q: Explain Torsional Moment with example?

A: The torsional moment, also known as twisting moment, is a couple that acts in a plane parallel to…

Q: Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal…

A:

Q: Kesis Kesit A r2 Secb o KesitB 80 M. |00

A:

Q: a) Determine the reactions at supports B (pin) and C (roller). b) Determine the internal loading at…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: 2. A non-rotating solid round bar with diameter of 2-in has a groove cut to a diameter of 1.8-in,…

A:

Q: A metal axle with second moment of area of 3,313.5 mm and radius of 15 mm is subjected to two…

A:

Q: Find the maximum shear stress and rate of twist for an applied torque Mi for the section shown in…

A: given; where;⇒t=thickness⇒a and b are dimensions. ⇒t<<a,b

Q: why underlin is p/2??? isn't just p??

A: Solution:

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

A:

Q: 1. A single-threaded 25-mm power screw is 25-mm in diameter with a pitch of 5mm. A vertical load on…

A:

Q: The expert has sketched FBD after cutting the truss as shown in the image (using sections method).…

A: In a method of the section, only those bar is taken as a force who is being cut. It does not mean…

Q: A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another…

A: Pressure angle, ϕ=20oTransmitted force, FA=11400 NDiameter of shaft, dshaft=52 mm

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: Calculate the reaction forces at A B and points in the figure.

A: Given data, A UDL of 400 N/m and UVL of 400 N/m to 800  N/m is given. To determine, the reactions at…

Q: Problem 3: 3D load reduction A combination of forces f1, f2, f3 (with magnitudes f, f2, f3,…

A: Representing f1,f2&f3 in cartesion co-ardinatef1=0i+0j+f1kf2=0i+0j−f2kf3=0i+0j−f3kResultant…

Q: Q-2 Figure below shows a shaft that is loaded as given, essentially in bending. Bearings are located…

A: Given data Diameter of the shat at B = D = 45mm Dimeter of the shaft at C = 55mm Shaft is loaded at…

Q: A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside…

A:

Q: Find the diameter of the spring wire and number of   active turns required

A:

Q: A solid 4340 HR Steel tie rod of length Lrod = 850 mm is employed to compress a 6061-T6 aluminum…

A: 4340 HR steel rod.Diameter of the rod, drod= 22.5 mmLength of the rod, Lrod= 850 mm6061-T6…

Q: the system is used to lift à mass of A compound lever as shown below. Find the effort 800kg. (10)…

A: As per policy experts are allowed to answer only one question (first one), for the second one please…

Q: Problems : Find the reactions for all of the followin problems: 4KN/m 12m 24m :-

A:

Q: unting for stress concentrations. calculate the safety factor for the material selected. if matrial…

A: Given-Information:- Material 4150 AnnealdF1 = 9 kNF2 = 13 kNF3 = 15 kN To-Determine:- Safety Factor…

Q: (10) A weight of 270kg falls a distance of 1.0m & strikes a coil compression spring which absorbs…

A:

Q: Need to find degree of freedom by using gruebler and kutzbach equations please.

A:

Q: 5.41 The inverted T-beam supports three concentrated loads as shown in the fig- ure. Find the…

A:

Q: ) Derive the flexure formula for the straight members?

A: Stresses caused by the bending moment are known as flexural or bending stresses. Consider a beam…

Q: For the beam in shown in the figure, determine the vertical displacement at c& and the rotation at…

A: The flexural rigidity is constant

Q: Solid steel post subjecting torsion. Given that the diameter is 75.05 mm, length is 2.5.05 m and…

A: Given   Diameter, d = 75.05 mm Length, L = 2.5 m Shear modulus, G = 78.08 GPa Torque, T = 540 N-m…

Q: Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter…

A: To design: The clamp coupling. Given: The shaft diameter is d=60 mm. The torsional moment is T=160…

Q: Use area method to draw the shear and bending moment diagram. Start with determining the value of…

A:

Q: A steel beam, of lengths a=5 m and b= 3 m and a hollow box cross section, is supported by a hinge…

A:

Q: For a weighing machine, the allowable load of 3000 N is loaded on a helical spring which it resulted…

A: Given:- F=3000N, y=60mm, Fs=2, c=4 τy=0.69 gpa and G=79.34 gpa Solution:- Step-1:- c=Ddwhere…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.