Find the magnetic force and the electric force per unit length (the force per unit length is simply the force divided by the length of the cable) exerted by a very long cable with linear charge distribution A, moving with constant velocity v, over another Very long cable, with the same load and speed distribution, in parallel and at a distance d from the first cable. At what speed must both cables move for the magnetic and electrical forces to compensate?

Find the magnetic force and the electric force per unit length (the force per unit length is simply the force divided by the length of the cable) exerted by a very long cable with linear charge distribution A, moving with constant velocity v, over another Very long cable, with the same load and speed distribution, in parallel and at a distance d from the first cable. At what speed must both cables move for the magnetic and electrical forces to compensate?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1) Design an electrical measurement device that can switch on an air cooler to work when the temperature is 25 C and the electrical power should be 220 V. Note the electrical power has reduced to 5V when it is 220 V by some circuits. You can use this signal m your device.
i need the answer quickly
An RC circuit includes a basic switch. In position "a", the battery, resistor and capacitor are connected in series, and the capacitor charges. In position "b", the battery is replaced with a short, and the capacitor will discharge. Two voltmeters and an ammeter have been added to the circuit. (g) Enter an expression for the current as a function of time. Your answer must explicitly reference the maximum current, Imax, that was determined in the previous step. h) Enter an expression for the voltage measured across the resistor, VR, as a function of time i) Enter an expression for the voltage measured across the capacitor, VC, as a function of time j) Add an expression for the sum of the voltages across the resistor and the capacitor as a function of time, VR + VC.
I am very lost on the steps it takes to complete these problems from start to finish, If at all possible can you please give a fairly detailed explanation of the steps you took to solve the problem. KCL, and KVL still confuse me and I'm unsure of how to get the equations on my own. I'm attempting to gain some helpful practice but find it hard when I don't understand how the equations were acquired.
The topic is about Applications of First Order Differential Equations. The problem given is about RL Circuits. The first image attached is how I want to answer the given problem which can be seen on the second image attached. Please provide a complete solution. (of how I want to answer it) Thanks! Will give you a thumbs up.
i need the answer quickly
Find c(s) R(S) R(s) + G1(s) G2(s) Answer G3(s) G4(s) G5(s) FIGURE P5 5 G8(s) G6(s) G7(s) G7 G₁ (G4+G3) ([G7 G6+ 1] G₂ G₁ + [G4 + G3] [G5 G₁ - G8 G7])+ (G7 G6 + 1) C(s)
You are given a driver with a capacitance of 2pF. What is the optimal load your circuit can drive with an optimal buffer chain of six stages?
Signal-Flow Graph Models Exercise-4: r, andr, are inputs and x, and x, are outputs a1:X1 + a12'X2 + r = X1 a21 X1 + a22 X2 + r2 = X2 40
Please show step by step solution. Determine the error ratio of the block diagram below using a) Block Diagram Reduction, and b) Mason's Gain Rule. H, E G, G, G3 C G, H,
Q2: Are the following two systems (given in the Fig.(2) cquivalent? Prove your answer using Mason's gain formula. R(s) H1 H2 HS ***** R(s) c(s) GI G2 GS H1 H2 H3