Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axis are 30o. Produce a graph of velocity ratio against angle for f to proof the calculated results.

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: taper angle and the set over respectively are

A: Given data,  Length of the shaft,L= 90 mm Tapered portion length,TL=55 mmD=80 mmd= 65 mm Determine…

Q: The figure below shows the components of normal forces, the value of radial force on the gear wheel…

A: Write the given value using suitable variables. Here Ft signifies tangential force, and 0 signifies…

Q: Q: Shaft rotates 3500 rpm clockwise and carrying gear A. Compute 1. the train value for the train.…

A:

Q: A straight spline has 10 splines and is Fit B. The required major diameter, D, of this spline…

A: Given data: Number of splines, N = 10 Fit = Fit B Torque per inch of length, T = 600 lb-in

Q: Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950…

A: Given: The speed of coupling, N = 950 rpm The taper angle, α = 25° The mean diameter, D = 120 mm

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of…

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Q: Figure (1) shows a schematic drawing of a countershaft which is part of the conveyor system and…

A: Figure (1) shows a schematic drawing of a countershaft which is part of the conveyor system and…

Q: 2. Shafts A and B are connected by rolling cones and are turning in the same direction. A makes…

A: A shaft is a spinning machine element with a circular cross-section that is used to convey power…

Q: Also, ISO, nna the maxmu

A:

Q: An 18 teeth sprocket driving with 98 teeth sprocket at a center distance of 34 pitches. Find the…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: Problem 2. 2000 rpm. Calculate the output The gear train shown below has an input speed nimput speed…

A:

Q: The figure shows a schematic representation of a gear system. The gears are meshed with one another…

A:

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: Please solve for the reactions at A

A:

Q: In a spur gear arrangement, the driver has 90 teeth of 38 mm pitch. Find the power, if it can…

A: Given that Pitch= 38 mm Tangential force = 130 N Speed = 100 rpm

Q: Bar AB rotates as shown with an angular velocity equal to 1O rad/s. Assume AB ha a length of 500mm…

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: a=75 mm b=160 mm c=20 mm determine the moment of interia Y prime

A: Given Data

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: An epicyclic gear train as shown in figure. Gear D has 65 teeth, gear C has 15 teeth and annular…

A:

Q: A 13 in pulley turns at 30 rpms find the constant of inverse variations

A: Write the formula for the constant of the inverse variations. Nd=k Here, k is the constant of the…

Q: Specify the location of all velocity centers in the following mechanism.

A: for solution refer below images.

Q: 8 6 C 111 D Pin 8000 T Pan A B - UT 5 t Compute the pin reactions at all of the pins

A: Given: The force acting between the point C and D is: →F=8000 N If the reactions at pin A and pin B…

Q: Calculate the torque.

A: The applied force is F = 89 cN = 0.89 NLength of crowbar L = 0.7angle = 80 degreeTorque is defines…

Q: 1-)The diagram of the change of cutting force for the cutting work performed with the press seen in…

A: Given data   Engine revolution =  900 rpm Flywheel revolutions = 60 rpm. Themoment of inertia of…

Q: The input shaft for the gear train shown rotates at 4500 rpm. Compute the train value and the…

A: The train value of any gear train is defined as the ratio of product of number of teeths on the…

Q: The shaft shown in the following figure is 200 mm long between self-aligning bearings at "A" and…

A:

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A:

Q: Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE.   Shafts A and B are…

A:

Q: In the given planetary gear system, the free end of Driving Shaft E has an angular velocity of WE =…

A: Given: The speed of the driving shaft E→NE=11.2345 rpm      (ccw) The radius of the each planet…

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: A cross belt drive has a 6 in. pulley driving a 48 in. pulley. The distance between their centers is…

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.