Find the general solution for the cantilever beam. Use initial displacement and initial velocity as y(x,0) = f(x)=-0.05x and y, (x,0) = g(x)=0, respectively on 0≤x≤10 m. Plot displacements of the cantilever beam y(x, t) at t=1s, 2s and 5s together in the same plot. FIXED END FREE END Fig. 2. Schematic of cantilever beam

Find the general solution for the cantilever beam. Use initial displacement and initial velocity as y(x,0) = f(x)=-0.05x and y, (x,0) = g(x)=0, respectively on 0≤x≤10 m. Plot displacements of the cantilever beam y(x, t) at t=1s, 2s and 5s together in the same plot. FIXED END FREE END Fig. 2. Schematic of cantilever beam

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the conjugate-beam method and determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70 x 10^6 mm^4
Find the linearization of f(x) = 3+∫1x2 sec ( t -1 ) dt at x=-1.
consider yhe beam shown in figure 1. El is constant Use the conjugate-beam method. Suppose thag M= 24k•ft and El is in k•ft^2 a) determine the slope at C measured counterclokwise from the positive x axis b) determine the displacement at C measured upward answer in k•ft^2/El please 6k M A C B 4 ft 6 ft
1. Given the vectors A = 5i + 3j + 2k and B = 10i – 7) – 2k. Find the following: (a) A. (b) Angle between A and B (c) Ax B (d) (A+B) x (A-B)
(b) Describe how to use the virtual work principle to find the horizontal displacement at D in the following figure (0) B 2L A L EI = constant Figure 2b L C D
Use Virtual work method Find the following; B (a) Rotation at C A (b) Horizontal displacement at C 12' 8 EI = Constant
Use the method of joints to determine the force in each member of the truss. State whether each member is in tension or compression. Assume every member is in tension when you analyze a joint, using + to denote a member in tension and – for compression. Use the components of the forces with EF, = 0 and EF = 0 to apply EF = 0 at a joint. The %3D y truss and loading are symmetric, so it's not necessary to analyze every joint. 2.25 m 2.25 m 13 kN 3 kN 13 kN D 1.5 kN 1.5 kN В F 1 m 1 m E 3 m 3 m 3 m
Solve for displacement at C and D using Conjugate Beam Method
Using the virtual work method, calculate the vertical displacement at A. Solve with the step chapter Analyze structure
QUESTION 1 (a) Sketch a bar element, a plane truss element, and a beam element. Label the axes, nodes and nodal degrees of freedom (dof). Identify the physical quantity of each dof. (b) Figure Q1(a) below shows a loaded cantilevered beam. The beam is made of a material with E = 200 GPa while the cross section of the beam is shown in Figure Q1(b). کسیس 2 kN/m 1 6 m 10 KN (a) 2 4 m 8 kN 40 kN-m Figure Q1 200 mm (b) 400 mm
Using the virtual work method, calculate the horizontal and vertical displacements at A and C displacements. Solve with the step the chapter Analyze Structure
Using the conjugate beam method show the solution, determine the slope and displacement of the pinB connected to the pin for the compound beam shown. Use E = 29 x 10^3 ksi and I = 30 in^4. The answer is -4.58 in. (displacement of point B) just show the solution..