Find the force F just sufficient to keep the quarter circle gate from opening. The gate is uniform and weighs G = 80kN besides the width is b = 2m. R = 2.1m. At point A - hinge

Q: The truss pinned to the floor at D, and supported by a roller at point A is loaded as shown in the…

A:

Q: Determine the force in member BC of the loaded truss. The force is positive if in tension, negative…

A:

Q: 1.) Determine the force in pin A and the force in member BD. Assume a = 525 mm, b = 275 mm, h = 400…

A: Given Data - a = 525 mm, b = 275mm , h = 400 mm P = 725 N and Theta = 60* To Find - Force in Pin A…

Q: 6. A truss ABC is subjected to a load F=10KN at pin D. The outside and inside diameters of bar AB…

A:

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the…

A:

Q: Determine the magnitude of force in member BD

A: Find the magnitude of force in member BD

Q: Two 160 mm * t cover plates are welded to two cahnnels 200 mm high to form the cross section of the…

A: Introduction : Reactions : One of the most basic structures is the simply supported beam. Only two…

Q: Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal…

A: Given: Link AC: thickness= 3mm, Width=12mm

Q: The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed…

A: Detailed solution is given belowSlight difference in answers due to rounding off Explanation:Step…

Q: 607 mm 605 mm C A B 25.5mm 53 mm f the gap between C and the rigid wall at D is initially 0.153 mm,…

A: Given. The load (P)= 205KN GAP BETWEEN CD =0.153 mm   Our aim is to calculate the support Reactions.…

Q: The equilateral triangles have sides of 2 m. The tops and bottoms of the equilateral triangles are…

A: Given, To find,  A) The Support Reactions.  B) Internal Member Forces.  C) Identify the nature of…

Q: RAH A 60⁰ RAV 500 N E 60° 3m 60⁰ RAV = 106.2 N O O RAV = 201.8 N O RAV = 365.72 N RAV = 123.5 N C D…

A:

Q: A 200-lb force (P) directed vertically downward is applied to the toggle vise at C. Knowing that…

A: Given Data : Length of AB= 4 in Length of BC= 6 in length of BD= 6 in Force (P)= 200 lb

Q: Two forces having a magnitude of 1000 N and 600N act on the ring. Determine the arigle 0 between the…

A:

Q: 6000mm 6000mm X kN ww A Y kN www 6000mm В C

A:

Q: 2 m 5 kN B Determine the force in member BC, in kN. 3 m 10 kN 5 m

A:

Q: The steel truss was subjected to horizontal force 2kN at C. Find the m of AC using the method of…

A:

Q: Determine the support reactions and all internal pin forces.

A:

Q: Problem Number 4. The steel truss was subjected to horizontal force 2kN at C. Find the member forces…

A: P = 2KN

Q: 700 N 800 N 566 N 60° 45 60° 45 30° 3 m 3 m А, 3 502 N Е, %3D 764 N (а)

A:

Q: P4.5 to P4.10. Determine the forces in all trusses. Indicate tension or compression. A L B 18 J C I…

A:

Q: Determine the magnitude of the pin force at B. 0 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A: To find out the magnitude of the pin force at  B.

Q: 6. Determine the force components at B and C, as they act upon member AC. 2.25 m 1,200 N BA DF (DF =…

A:

Q: The steel truss was subjected to horizontal force 2kN at C. Find the member forces of AC using the…

A: Calculation of Member forces in AC using Unit Load METHOD##

Q: plate. If the forces are concurrent at point O, determine the magnitudes of F and T for equilibrium.…

A: For any system to be in equilibrium, equilibrium equations must be satisfied. Here the system has to…

Q: The neutral axis of the cross-section a beam is that axis at which the bending stress is A. infinity…

A:

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T…

A: Calculating the total area of T-Cross section A: A=(7*1.5)+(6*1)   =16.5 in2

Q: 35° 35° 2.5 m 2,5 m tiskN 15 kN

A: Rod are rigidly Joined

Q: 8 kN 45 D T. 5 kN

A: Free Body Diagram of the given problem:

Q: H, a a a

A:

Q: Problem #4 Y KN G 30° 10 m celee B X KN 60° 60% 10 m A KN Good E 30° D 10 m Determine the force in…

A:

Q: 67. A single angle in tension is connected by one only. If the areas of connecting and outstand legs…

A: Given data:  A single angle in tension is connected by one leg only. The areas of connecting legs =…

Q: 4. Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile…

A:

Q: Hydrostatic Forces Vertical Plate A rectangular plate is 2 m wide and 3 m tall. It is oriented…

A:

Q: 4-46. If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support…

A: Given : P = 200 kN A-36 steel Determine the support reaction at A and D ?

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.