Find the coordinates of the centroid (to the nearest 0.01 in.) of the uniform flat plate machine part shown.

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: 12-x2 了了少 Je

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: Determine the maximum deflection of the 70-mm-diameter A-36 steel shaft.

A: To find: The maximum deflection of the 70 mm diameter steel shaft. Given: The diameter of a steel…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: Determine ly and ky.

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: Assume oz = 500, ay = 300, Txy = 250, oyicld = 350. Answer the following questions. Click here for…

A: GIVEN DATA σx= 500MPa σy= 300MPa τxy= 250MPa We have to find maximum and minimum normal stress on a…

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: What is the average shear stress?

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: name these lines

A: The names of the given lines is given below.

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Q: 50 mm 150 mm 50 mm 85 mm Section X-X 20 kN

A: Let us shift the load to section X-X. The moment M and force P will create the same effect.

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: At a certain instant, the particle of mass m has the position and velocity shown in the figure, and…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.