Find the centroid of the shaded portion as shown in figure. Where b1 = 85 mm, d1= 55 mm, R =12 mm, C = 21mm b1 d1 R

Q: Determine the x coordinate of the given composite figure. The value of b is 4 inches.

A:

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: Please refer to the figure below. If r= 550 mm. Determine: A. Rectangular form of r in m. B. Unit…

A:

Q: 0 5 10 38.3 cm 3.83 cm 33.83cm 33.3 cm

A: Ans: 3.83 cm

Q: Compute Ix (I sub x, in inches4, round-off to 2 decimal places) for the region shown.

A:

Q: 3.00- 1.25-

A:

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston…

A: here, stroke bore ratio say, l/d ratio = 1.2 so, l = 1.2×d volume per cylinder = π4·d2·l here,…

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: 4. What is the complement of a 72°21'47" angle?

A: We know that the complement angles pair have sum = 90o let x =  72o 21' 47"  (Given) Complement of x…

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: Compute Ix (I sub x, in inches“, round-off to 2 decimal places) for the region shown. 4

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: need help finding dimension x and y in the casting shown 2.80 cm 5.20 cm 6.00 cm 2.50 cm E 7.20 cm

A: Draw a diagram for the given problem.

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Outside diameter, do=5 inInside diameter, di=4 in

Q: :Find dimension y all dimensions are in inches 0.664 R 58°50' 2.800 R 1.120 0.400 R

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Express the quantity 254,998m in cm.

A: Given: The quantity is Q=254998 m. The unit conversion factor to convert Meter into Centimeter is, 1…

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.