Find the area of a piece of land with an irregular boundary as follows: 5.59 3.38 3.96 480 2.30 O+000 Ot0IO O+020 Ot030 O+040 The stations are on straight line boundary. Find the area of the land by Simpson's One Third Rule.

Q: Air duct straps are made from a 1-inch-wide strip of metal. The metal is 2463⁄4inches long. Each…

A: Calculate the numbers of straps of metal used for air duct. The length of metal is 24634inches.…

Q: What is the type of this truss

A: Solution: There are different types of trusses used in the construction field like Howe Trusses…

Q: When are shear plates used?

A: Shear Plate :  1.shear plate connectors provide a large bearing surface to resist shearing-type…

Q: The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete…

A:

Q: 120N 80N 300

A:

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: Q4: Prove that:

A:

Q: How many centimeters long is side AC?

A:

Q: Explain pipe earthing

A: Brief concept- Earthing- It is a process by which charge is transferred to the earth with the help…

Q: one help please can you help me to draw an isometric view of the bridge (truss)

A:

Q: Write short notes on the following topic with proper figure. (6) i. Wrinkling ii. flattening iii.…

A: BASIC DESCRIPTION:  Mandrel tube bending, using a mandrel…

Q: Define the term Fastener Spacing?

A: Fastener Spacing : Pitch is centre to centre spacing of the fasteners in a row, measured along the…

Q: Problem 1 Wind blows on the side of a fully enclosed agricultural building located on an open flat…

A: When wind engineering is used to analyse tall buildings, the major load is frequently found to be…

Q: Define the Tensile load transfer ?

A: Solution: Tensile load transfer is defined as a measure of the capacity of a material to stand up to…

Q: draw stair tread and riser = 270 & 187 mm stair slab and landing thickness = 150 mm

A:

Q: Define the Stresses Along the Vertical Axis of Symmetry ?

A: Solution: Stresses that are acting on  normal face in a negative direction. Stresses are the forces…

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: Discuss Designing for Shear

A: Introduction : Shear stresses in design normally operate in planes perpendicular to a member's…

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: 250mm 250mm Reinforcing Bars

A: Given:-size-250mm x 250mmload =400kNallowable stress=8MPa for concrete and 150MPa for…

Q: Complete an interpretation drawing that show permissible surface condition that lies partiall part…

A: The permissible surface condition is as follows. When a tangent modifier is added it only controls…

Q: What is a contraction joint?

A: In the construction process, there are three types of joints. They are Contraction joint, Expansion…

Q: What is Jet grouting?

A: The jet grouting can be defined as it is a soil stabilization or ground improvement method which…

Q: draw depth of stair landing = 1200 mm  floor to stair landing height = 1500mm

A: Given depth of stair landing = 1200 mm  floor to stair landing height = 1500mm To draw a staircase…

Q: This is a static mechanics question Question : give a clear definition of the term “ Space Truss” (…

A: To define space truss

Q: Define spudding

A: For drilling a well in a gas and oil industry, this process is used at the beginning.

Q: SOLVE US ING CANILEVER METHOD 31|KN hi E F D 696KN ヤ G Li

A: Given  P1=311 KN   and P2 =696 KN using cantilever method inetior column takes double horizontal…

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: What is Spudding?

A: Spudding is defined as a process in which the drilling process of a well in any gas and oil industry…

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: 10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B)…

A: Warning  is being given before answering,  However I do my best.  I try to give good explanation…

Q: When do shear plates become necessary?

A:

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: Define Vibrocompaction.

A: Vibrocompaction is a method in which the density of granular soils is increased to the appropriate…

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: What is  negative skin friction ?

A: Friction is the resistance to motion of one object moving relative to another. It is not a…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: How i got shear force X zero point?

A:

Q: Describe the term compressibility.

A: Compressibility:- It is defined as the capability of the soil to decrease its volume under…

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam