Find the amount of load to be lifted for the lifting speed of 0.2m / s, given that a 10kW motor is given in the system in the figure. (All the bearings in the system must be slipping, the efficiency of the reducer shall be 0.94.) Zi = 10 M. brake pulley ($200) Z2 = 100 V = 0,2 m/s Q a) 5.6 ton b) 4.4 ton 2.8 ton d) 1.4 ton e) 6.2 ton

Find the amount of load to be lifted for the lifting speed of 0.2m / s, given that a 10kW motor is given in the system in the figure. (All the bearings in the system must be slipping, the efficiency of the reducer shall be 0.94.) Zi = 10 M. brake pulley ($200) Z2 = 100 V = 0,2 m/s Q a) 5.6 ton b) 4.4 ton 2.8 ton d) 1.4 ton e) 6.2 ton

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the angle 8 of rotation of gear A relative to gear D. Use G =12x106 psi for the shaft. poutside - 4 in pinside = 2.1 in 600 lb-ft 1000 lb-ft GG B 900 lb-ft D 4 ft- 18+/- 30 + 50 ft- -5 ft- 500 lb-ft A X
STRENGTH OF MATERIALS (Please answer ASAP. No long explanation needed.Thumbs up will be given) The compound shaft, consisting of a solid steel (diameter = 140 mm) segment and hollow aluminum ( outer diameter 120 mm, wall thickness = 10mm)) segment, carries the two torques shown. Determine the maximum permissible value of T subject to the following design conditions: τst ≤ 93 MPa, τAl ≤ 50 MPa, and θ ≤ 4o (angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminum. Include the FBD of each segment and show the internal torque. DISREGARD THE GIVEN DIAMETERS IN THE FIGURE.
The turnbuckle shown in Figure has a square thread with a mean radius of 5 mm and a lead of 2 mm. If the coefficient of static friction between the screw and the turnbuckle is 0.25, determine the moment M that must be applied to draw the end screws closer together. Choices: A. 6.36 N-m B. 7.36 N-m
1. Equilibrium 1.2. A lift, comprising of 3 cables arranged as shown, carries a spare part for amilitary tank. Compute for the tension experienced by the 3 cables given that thebody it carries is 8 Mg
(c) For a Pelton wheel with a fixed turning angle ß (less than 180º), radius r (r > 0), fluid density p, jet velocity V¡, volumetric flow rate V, and angular velocity w, the angular velocity w and radius r are constrained by the following relation krn, W = where k and n are positive integer constants. For this design: i. Derive an expression for the ideal shaft work.
Read the question carefully and give me right solution with clear calculations.
Asap !!
I need a quick solution within 15 minutes With my best wishesTon.
Show complete and neat solution. GRESA FORMAT: Given, Required, Equation, Solution and Answer
Q4- If the mass of cylinder A is 30 kg, determine the mass of cylinder Cin order to hold the assembly in the position shown. 30 kg
A carpenter holds a 17-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board, determine the forces at A and B (use positive if the force is up and negative if down). Answers: NA = NB = i i B 9¹ lb lb
Item 2 of 2 In figure shown, the mass of block A is 50 kg. The coefficient of static friction for all surfaces of contact is 0.10, determine the minimum mass of B to maintain equiliorium of the system. Assume the pulleys to be frictionless and use B = 75°, e = 70° and a = 65°.