1910 mm10 mm30 mm10 kN30 mm10 KN25 mmThe bottom force of 10 kN is 25 mm below the centroidFind stresses at pt A when:the upper 10 kN force is at the centroid, then 15 mm above centroid, and 25 mm abovethe centroid

Answered: Image /qna-images/answer/31842148-4b8e-4e1e-a07a-fe1724617866.jpg

Answered: Find stresses at pt A when: the upper…

Find stresses at pt A when: the upper 10 kN force is at the centroid, then 15 mm above centroid, and 25 mm above the centroid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem # 1: For the trussloaded as shown, calculate the axial stress developed in members CD, ND and NK.Use A=20in2. ( 15 t 15 ft 111 920 lb 1145 lb 1760 lb -20 it20 n 20 t20n-201-20 t-
a beam is supported by a pin support at A and a roller support at B. For this question, leave your answer in terms of the variables w and L. (a) Using equilibrium of the full beam, find the support forces at A and B. (b) First section: Make an arbitrary cut between points A and B. Take the distance of the cut to be x along the beam from point A. Draw the free-body diagram for the left section and find functions for the internal shear force, V(x), and bending moment, M(x), in the section of the beam between A and B. (c) Second section: Repeat part (b) for the section of the beam between B and C. Take x to still be the distance from point A. (f) Find the value of x at which V(x) = 0. The internal bending moment reaches a maximum at the same point as V(x) = 0. Find the maximum bending mo- ment. pin Sketch the shear and bending moment diagrams. B L W C roller
3- Compute minimum force F which barely prevent block A from sliding. Block B is connected to a rigid point by a cable. WB= 60 Ib B We WA-120 Ib WA A F $25° f=o. For all supporting surfaces
Solve for question 1. And the question below as well thank you
Statics and rigid bodies. Complete solution
The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The normal force acting on a plane to the cylinder is 10 KN. Assume smooth surface, the cylinder leaned to a vertical rod of 8m long and has a weight of 5 KN which was supported by a cable and a hinged (as shown). Find the tensile force of the cable holding the rod and the reactions of hinged to support the cylinder from sliding.
- Two pipes, each with a diameter of Im, are supported every 10m by a frame, as shown in the figure. Each pipe (including its contents) weighs 2.0 kN/m. All contact surfaces are assumed to be frictionless. Determine the support reactions. 1.8m A 2.4 m B 2.4 m
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is SELMA KAUNALENGA V applied at B where P = 18i - 11j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. 2. C 4 m 6 m y P. Answer: Calculate the magnitude of the tension in cable BD in kN. Answer: II 2 m 6 m 3 m
Q4) Calculate the reactions at supports. 400 N/m 400 N/m
For the pinned frame in the figure, calculate the pin forces acting at point B, on member BD (magnitude and direction).Hint: Look for two-force members
e The two-steel shaft shown in figure have the same diameter and weight 170 lh cach. Neglect the friction at all contact surfaces and find the reaction of the wall at A on the lower shaft
Take point H in the = 1. (Outcome 2) A submarine is 30 m below the surface of the ocean. (You may = 1.6 figure to be at the 30 m depth.) The circular hatch is hinged at point H and has diameter D Find the net m. The hatch is inclined at an angle of 30° to the horizontal as shown in the figure. force required to open the hatch when applied as shown in the figure, perpendicular to the hatch. The pressure inside the submarine is equal to the atmospheric pressure and the density of sea water is 1030 kg/m³. Note that the area moment of inertia for a circle about a diameter is equal to where R is the radius of the circle. (Hint: Do not try to solve this problem by solving for vertical and horizontal forces separately!) 30 H F D= 1.6 m