Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442-9 Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from the leading edge. The fluid is water at 60°C with a velocity of 2 m/s. The plate maintains a uniform temperature. Assume the film temperature to be 40°C. 6442-9 Is the flat plate losing heat to or gaining heat from the water flow? Justify.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an Osborne Reynolds Demonstration experiment, why is it the in laminar flow, the color collected has a color unlike in transitional and turbulent flow where the color of liquid is just transparent?
Water at 45° C flows over a large plate at a velocity of 25 cm/s. The plate is 1.2 m long in the flow direction, and its surface is maintained at a uniform temperature of 10° C. Calculate the steady rate of heat transfer per unit width of the plate.
i need the answer quickly
Oilflow in a journal bearing can be treated as parallel flow betweentwo large isothermal plates with one plate moving at a constant velocityof 12 m/s and the other stationary. Consider such a flow with a uniformspacing of 0.7 mm between the plates. The temperature of the upperand lower plates are 47°C and 17°C, respectively. By simplifying andsolving the continuity, momentum, and energy equations, determine:(a) thevelocity andtemperature distributionsin the oil.(b ) the maximum temperature and where itoccurs.(The location ofmaximum temperature is determined bysetting dT/dy=0).(c) the heat flux from the oil to each plate
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.
Air is flowing at 35°F with a velocity of 12 ft/s over a plate 10 ft long and 2 ft wide. The plate is at room temperature. Determine the coefficients of local friction, heat transfer coefficient and heat transfer rate of the plate at 1 ft intervals along the length. Plot on the same graph the results as a function of distance from the leading edge, the graph will be reviewed. The table of thermal properties of air is on the platform. Report in the following boxes your results for a length of 5 ft.
An incompressible fluid flows over a flat plate with zero pressure gradient. The boundary layer thickness is 1mm at a location where the Reynolds number is 1000. If the velocity of the fluid alone is increased by a factor of 4, then the boundary layer thickness at the same location, in mm will be 415
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
In a laminar flow over plate the thickness of hydrodynamic boundary layer is 2 mm. What will be the thickness of thermal boundary layer? Fluid properties u = 4 x 10-4 kg/m-s, k = 0.664 W/mK, Pr = 2.54