Find Ic(t) for every time

Q: Define Ohmic region of FET characteristics and Write down the relation between VGS and ID?

A:

Q: Expalain the four components of electric circuit ?

A: The four main component of any electric circuit is battery which is used to supply voltage to the…

Q: Explain the environmental hazard of Nuclear power generation with neat diagram

A: Nuclear power plants use uranium as fuel. During the process of mining uranium released high amounts…

Q: The main objective in the principles of electrical safety is to protect human from electric shock,…

A: there are two fundamental steps to prevent human from contact with electricity .

Q: 2 The wire shown has a current being carried to the right and point P is a distance r away from the…

A: By amperes law magnetic field due to long current carrying conductor is I2π×ρ where I is current…

Q: What documentation is needed before work on, near or associated with high voltage is carried out?

A: Work near or associated with high voltage should be done carefully and under supervision.

Q: WHATS RTC IN ELECTRICITY?

A: The solution is given below

Q: Define slew rate with the formula and its unit.

A: Generally slew rate is calculated in analog electronics. Where it is defined as the rate of change…

Q: 70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit…

A: While calculating the conductor size for a continuous load, take 125% of overloading conditions…

Q: nduction heating area of application and merits

A: The process of heating an electrically conducting object electromagnetically using heat generated…

Q: A welding power source must not be used continuously in long time without care. The rated duty cycle…

A: Given Rated welding current =350 A Maximum welding current usage =300 A Rated duty cycle =60 % To…

Q: Advantages and Disadvantages of using Wind energy.

A: Wind energy is one of tje most commonly used energy source for the generation of electricity using…

Q: The electrical energy that is produced will be a part of the. energy applied to rotate th The number…

A: To fill up the blanks

Q: 4- A 100kW, belt driven shunt generator running at 300rpm on 220V bus bars continue to run as a…

A: Generated emf = terminal voltage +voltage drop in armature resistance +brush voltage drop. Back emf…

Q: a) A moving coil instrument whose resistance is 5002 gives a full-scale deflection with a current…

A: Permanent Magnet Moving Coil (PMMC): A PMMC meter, also known as a D'Arsonval meter or galvanometer,…

Q: Discuss in detail different types of induction heating with the help of neat

A:

Q: parte A • Develop and explain the electrical schematic for the excitation coil in series. • Develop…

A: It is asked to develop and explain the electrical schematic for the excitation coil in series and in…

Q: Q3/ Discuss the advantages and disadvantages of shielding the copper cables .

A: Shielding reduces electrical noise through the copper cables transmission shielding the copper…

Q: 2. Explain electrical contact resistance. Holm model of electrical contact resistance. Contact…

A: It is asked to explain contact resistance and the Holm model of contact resistance. Also it is asked…

Q: a) Using appropriate diagrams, explain the skin effect and skin depth.

A:

Q: A copper cable has a resistance of 17 3 ohms/km at 90°C. What is the resistance of 118m of this…

A:

Q: Create a Sequence Diagram about Temperature Controlled Electric Fan with the following: *Thermistor…

A: Sequence Diagram of temperature controlled electric fan shows that how the fan works with the sensor…

Q: a) An SCR based AC power controller circuit is given in Figure 1. The circuit connects a 240V 50Hz…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Explain with a neat sketch the function of super heaters and economizer.

A:

Q: 6 A lamp filament is to have its resistance measured by the voltmeter/ammeter method. The test…

A: In this question,  Determine the percentage error?  If circuit is connected long shunt and short…

Q: 6. A length of a copper telephone line has a resistance of 24 ohms at 20°C. What is the resistance…

A: Note: As per our policy we can solve only one question, please re-upload the remaining question as a…

Q: What are the factors responsible for the execution of Spark?.

A: To do:We have to explain the factors responsible for the execution of Spark.

Q: Briefly explain why it is important to consider the effects of temperature changes  when designing…

A: Various electronic components are designed to work for a specific range of temperature, when the…

Q: Why there is a need to study Electrical skill problems?

A: Electrical skiil

Q: A circular disk of radius a is uniformly charged with ps C/m. If the disk lies on the z = 0 plane…

A: Solution- Given, The circular disk of radius (a) is uniformly charged with ρs C/m2.  In the above…

Q: I need the answer quickly

A: a) Heat transfer rates at  the absorber, desorber, evaporator and condenser are- QA=m(h24-h23)…

Q: why do you think renewable energy sources are important?

A: The explanation is as follows.

Q: Q2 / explain the operation of spit phase motor

A:

Q: What do you think are the most important electrical properties of agricultural products and why?

A: Agriculture materials : agriculture materials  is used to do agriculture work like harvesting ,…

Q: b) Explain why the effective length is less than the total length of a laminated armature .Which…

A: Lamination is used in machines ( Transformer and rotating Machine) to Reduce the eddy current…

Q: The Design of Distributors depend on which parameter? A. CURRENT CARRYING CAPACITY B. HIGH POWER…

A: Given To determine the parameter which affects design of distributors

Q: Q5) W. bridge at state of balance when first arm 10002, second arm 2000, third arm 1002 and forth…

A: