Find and draw the Thévenin equivalent circuit for the network external to the resistor R for the network in Figure below.  2. Find the power delivered to R when R is 100 Ω.

Q: Derive current divider rule formula

A: The solution can be achieved as follows.

Q: 5. What is the function of the digital circuit shown below? Describe its operation briefly and find…

A:

Q: 2. The three terminals of the BJT are called: a) Larry, Moe, and Curly b) Thing-1, Thing-2, and…

A: BJT (bi polar junction transistor)   BJT have three terminal, name of Three terminal of BJT?

Q: Comparison of types of analogue to digital conversion؟

A: Types of ADC Dual slope ADC Flash ADC Sigma delta ADC Successive Aprroximation ADC

Q: Discuss the different types of transistors used in microchips and how they work.

A: Microchips, also known as integrated circuits, are miniature electronic devices that house…

Q: For proper operation of an N-channel JFET the gate voltage needs to be _____ with respect to the…

A: in JFET current through the device is controlled by the application if gate current .  There are two…

Q: In a self-biased JFET circuit, the gate bias voltage is actually developed as a voltage a. load…

A:

Q: 4. Build an AND gate using transistors, switches and LEDs. Pressing the switch should emulate…

A:

Q: The mass of a large computer system is 290 lb. How many kilograms is this mass?

A: Given data, The value of mass of computer is 290 lb. Since 1 lb = 0.453592 kg

Q: Make a list of three technologies that have gone from analogue to digital. What was the reasoning…

A: Analog devices works on a continuous type signals while digital signal works on discreate type of…

Q: Distinguish between ‘Analog and Digital signals’.

A: Analog signals A continuous signal called an analog signal substitute one time-varying quantity for…

Q: 9

A: For 9th question The given memory types are 1.ROM 2.RAM 3.EPROM 4.EEPROM For 10th question Sine wave…

Q: Question 4: what is the effect low cost operation amplifier in optical fiber system ?

A: Optical fibres are most commonly employed to convey light between the fibre's two ends, and they're…

Q: Explain any two signal presentations in the measurement system with neat diagrams

A:

Q: Find a device, which do not require the snubber circuit. a. SCR O b. Diode O c. IGBT d. MOSFET

A: Given To find device which do not require snubber circuit

Q: Discuss in detail about the evolution of electrical/ non- electrical Communication methods and…

A: consider the given question;

Q: Have a look at the problems that have surfaced because of the widespread use of digital materials.

A:

Q: What are the different types of memories and what are the applications they are used for?

A: Different type of memories

Q: The JFET terminals that are connected to thechannel are the A. Gate and sourceb. B. Drain and…

A: Drain and source are the  JFET terminals that are connected to the channel.…

Q: transistor connection indicate? Please select one: a. 0.7 V b. V_CC c. 0V d. OL

A: Answer is D) OL

Q: Punch Trough IGBTs have........... voltage blocking capabilities.

A: The IGBT is insulated-gate bipolar transistor. Based on structure the IGBT classified as, Punch…

Q: What is the difference between TVS and Varistor? And briefly explain which one to choose and when?

A: TVS diodes and varistors are both types of voltage suppression devices used in electronic circuits,…

Q: What is transistor in electronic

A: A transistor is a fundamental semiconductor device used in electronics to amplify and switch…

Q: Find the current I1 through R1 for the network method in Figure below.

A: Given circuit is,Asked to find the current I1 through resistor R1

Q: The following program is supposed to add the contents of memory location 2050H to the accumulator.…

A: When the above program is executed once, the contents of the accumulator will get updated with the…

Q: How does a transistor compare to a physical switch in a digital circuit? Use illustrations.

A: As we know that transistor works as a switch in saturation region or in cutoff region. Cutoff region…

Q: a. Find and draw the Thévenin equivalent circuit for the network external to the resistor R for the…

A: In this question, we need to determine the Thevenin equivalent across the terminal resistance R and…

Q: How transistor work

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: What is assertion and give region of it in time slot.

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: with neat diagram explain the construction and working principle of encoder.

A: Encoder is a disgital displacement transducer which is used to measure the displacement,

Q: When comparing a gate and a circuit, what are the key distinctions?

A: In the field of digital electronics, gates and circuits play fundamental roles in designing and…

Q: Using the superposition theorem, determine the current through the 24 Ω resistor of Figure below.…

A:

Q: If the range of measurement is from -2 V to 2 V, what should the number of bits of the ADC be in…

A: The voltage span is 2--2=4 Resolution given is  0.125 V

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).