Find and define "measurement of infiltration" Show illustration.

Q: Write about Lightweight Insulating Concrete Fastener Withdrawal Test per TAS 105 Protocol procedure.…

A: TAS (Testing Application Standard) protocols are typically developed and published by regulatory…

Q: Explain actual failure surfaces for passive pressure condition and effect on wall—Coulomb analysis.

A: Passive Earth Pressure: Full value of passive earth pressure is mobilised when the soil is on the…

Q: Uniform, and Non- uniform flow

A: uniform flow= when parameters of fluid like velocity and depth etc. won't change with space at any…

Q: What is the contaminant plume, or simply plume?

A: Plume refers to contamination in air as well as water. If we simply consider plume then the word…

Q: What is the major difference between horizontal and vertical spray chamber scrubbers?

A: Spray chamber scrubbers-Spray scrubber is the cylindrical or rectangular chambers in which gas is…

Q: List only Two of the following: 1) The Purpose of Water Demand with the percentage of each purpose.…

A: This question is related to the Environmental Engineering from Civil Engineering. As per question we…

Q: What were fly-ash ESPs?

A: An electrostatic precipitator is defined as a filterless device that excludes fine particles, for…

Q: What is Liquid circulation rate in a scrubber?

A: Solution: The rate of flow of liquid in a scrubber is generally explained in the terms of…

Q: Define the disadvantages of curing by ponding and polythene sheets?

A: The purpose of curing is to reduce the rate of heat loss of freshly placed concrete to the…

Q: Define about Prefabricated Vertical Drains ?

A: In construction of various structures on compressible, saturated soils like soft clay, excessive…

Q: penetration testing involves

A: Penetrating test is a simple and economic test done in soil by penetrating or boring a hole in soil…

Q: List the factors that may affect screening / sieving. (Consider both dry and wet and provide proper…

A: This question is related to the Geotechnical engineering from Civil Engineering. In this question…

Q: What is the major requirements for design and installation so as to achieve a properly operating…

A: Foundation drainage is an external drainage system built on the outer side of the foundation wall…

Q: Illustrate the typical layout of a grouting plant. Also mention the basic items required for a…

A: The cracks in concrete are injected with material to increase the strength is known as grouting .…

Q: What is the relation between the filtration time, run time, cleaning time and the number of…

A: by the filtration theory , the cleaning cycles can be calculated by tf=Ntr+tc-tc where,tf=time…

Q: Explain how can we stop leakage started on a basement due to increasing water table outside the…

A: Leakage can be slowed by sealing cracks and joints, but fails over time unless the water table…

Q: What is pipe flow? Describe the various types of minor head losses in pipes.

A:

Q: What are the disadvantages of sand plumbing?

A: Sand Plumbing- Sand plumbing describes a pipe that either contains sand or acts as a route for it.…

Q: What advantages or disadvantages does dry scrubbing versus wet scrubbing technologies have when…

A: The main advantage of scrubbers is the continual use of cheaper bunker fuel and thereby reducing…

Q: Write down the primary reasons for having limitations on the sizes of particles used to construct…

A: A Drainage filter is provided at the downstream slope of dam to prevent seepage under the base of…

Q: Write a detailed note on Blasting related to ground subsidence.

A: An explosive is a chemical compound or mixture of compounds that undergoes a very rapid…

Q: Describe about the vibrodisplacement procedure.

A: Vibro displacement is the ground improving method that is designed for compacting solid ground…

Q: Q#1: a)Differentiate between Sewer & Sewerage, Temporary & permanent Hardness, Inflow and outflow…

A: a)  The waste of humans that exits the home and runs into the sewers is referred to as sewage.

Q: what is the effect of alkalinity on flocculation?

A:

Q: LIST THE EQUIPMENTS ONLY NEEDED FOR THE ITEM OF WORK

A:

Q: Describe the methods and analyses used to examine the relationship between porosity, particle size,…

A: Porosity or void portion is a proportion of the void spaces in a material, and is a small amount of…

Q: What are the advantages of wet scrubbers?

A: Solution: The advantages of the wet scrubbers are that 1. It has the ability to handle the moisture…

Q: dure of using depth dial gauge to measure the depth of corrosion. Concise and clear.

A: A depth gauge typical refers to is a precision measurement instrument that is used by mechanical…

Q: Define coefficient of consolidation.

A: Coefficient of consolidation:

Q: Explain how effective backwash systems in the clearing or desilting of infiltration galleries?

A: Brief concept introduction- Backwashing- When the filters of the media get filled with solids such…

Q: What should you enter for the Total HAWB on the Consolidation Manifest? 2 34 14 20

A:

Q: Discuss the following:1. The possibility of a combined wet scrubbing and gas stripping process.

A: Solution: There is the possibility of the combined wet scrubbing and the process of gas stripping as…

Q: Define Subgrade Reaction Method.

A: Subgrade reaction method:

Q: Define the types of piston sampler ?

A: Piston Sampler:- When taking specimens in very soft to hard clays, the piston sample is designed.…