Figure Q5 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 120 mm, and knowing that P1, P2 and P2 are 10.a kN, 5.b kN and 15.c kN, respectively. Parameter a, b, and e are given by: a = last digit of your matrix number b = fifth digit of your matrix number c = fourth digit of your matrix number For example, a student with the matrix number CD200187 will have the values of 10.a = 10.7, 5.b = 5.8 and 15.c = 15.1. (a) Calculate the state of plane stress at point H (b) Sketch the element for the state of plane stress in (a) Using Mohr's circle, determine the principal planes, the principal stresses, and sketch the corresponding element at point H (c)

Figure Q5 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 120 mm, and knowing that P1, P2 and P2 are 10.a kN, 5.b kN and 15.c kN, respectively. Parameter a, b, and e are given by: a = last digit of your matrix number b = fifth digit of your matrix number c = fourth digit of your matrix number For example, a student with the matrix number CD200187 will have the values of 10.a = 10.7, 5.b = 5.8 and 15.c = 15.1. (a) Calculate the state of plane stress at point H (b) Sketch the element for the state of plane stress in (a) Using Mohr's circle, determine the principal planes, the principal stresses, and sketch the corresponding element at point H (c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. AB=X 2. A+B=X 3. X=A 4. ABC=X 5. AB+CD=X 6. AB+A=X Page | 4

Q: Determine the value of x and y, 3x + 5jy = 0 O x= 0 , y = 0 O x = 3, y =0 O x = 0,y = 5 O x = 0, y =…

A: Write the given expression. 3x+5jy=0

Q: Some homes that use baseboard heating use copper tubing. Hot water runs through and heats the copper…

A: Mass of the copper tube,(m)=540 g. Initial temperature,(T1)=15.01oC Final temperature,(T2)=25.48oC…

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

Q: Sketch the right oblique view name front view(F) and top view(T) and side view (S) on the sketch…

Q: Any repeating decimal number is a rational number

A: The first statement is true. Any repeating decimal number is a rational number.

Q: Given the two views of a solid and an auxiliary reference plane, draw the auxiliary view and…

A: Draw Auxiliary view of the given figures.

Q: Write the G-code with describe each lines : 20.0 40.0 40.0 40.0 60.0 30.0

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: as soon as

Q: dy Solve the differential equation cos(z) dz

Q: Not yet answered The toggle mechanism shown (Figure below) moves from an initial angle e = 30° to a…

Q: A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine the…

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 1 3. 9 TypehereIG 2.

A: Correct option: True.

Q: a powerp u, a process design id wastes (MSW) per hour. In an industrial boiler, MSW is burned to…

A: To given thatH1=104.93Kj/kgH2=2675.53kJ/kgH3=2942.73kJ/kgH4=3324.63kJ/kg

Q: QI\ AFind the value of the complex number (1- i) ?

Q: In the figure below, Which of the following represent the dedendum

Q: As fluids flow through pipes, energy is lost due to friction which produces energy loss and power…

Q: er the arm shown in Figure 1. rd kinematics problem. on of the end effector (x; y; z)* , solve the…

A: Kinematics - Kinematics is the part of mechanics which informs us regarding the movement…

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: Respond with TRUE if the symbol of the valve showll 4 2.

A: The symbol of valve is given

Q: Which of the following statement is correct? Select one: Speed is a Vector & Velocity is a Scalar…

A: Speed is a scalar quantity – it is the rate of change in the distance travelled by an object.

Q: DRAW THE ISOMETRIC FIGURES OF THE ORT

A: According to the details provided in the question, we need to draw an isometric view

Q: 01: Write G code to Write the first Letter of you name

Q: Your car workshop is attended by a customer that drive a Ferrari F355 coupe for some maintenance…

A: The wrench widths given are: No Wrench Width(in) w1 1/2 w2 9/16 w3 7/8 The nut sizes…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: DRAW THE ISOMETRIC FIGURES OF THE ORTHOGRAPHIC DRAWINGS BELOW. ADD DIMENSIONS AND LEADERS

A: According to the details provided in the question, we need to draw an isometric view

Q: 5. For the next festive season two competing firms (Firm A and Firm B) are drawing their promotional…

Q: Which of the figure is incorrect, left or right? 50 25 20 20- 40 20 20 20 12 12 - 20 Left O Right

Q: The ratio of lengths bla is exactly 7. W has a mass of 15kg. Find the force F in Newtons that…

A: Given data, The ratio ba = 7 Weight W = 15×9.81 = 147.15 N To determine, the magnitude of force F

Question

a=0

b=0

c=2

please answer quickly

Q5
Figure Q5 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 120
mm, and knowing that P1, P2 and P2 are 10.a kN, 5.b kN and 15.c kN, respectively. Parameter
a, b, and c are given by:
a = last digit of your matrix number
b = fifth digit of your matrix number
c = fourth digit of your matrix number
For example, a student with the matrix number CD200187 will have the values of 10.a = 10.7,
5.b = 5.8 and 15.c = 15.1.
(a)
Calculate the state of plane stress at point H
(b)
Sketch the element for the state of plane stress in (a)
Using Mohr's circle, determine the principal planes, the principal stresses, and
sketch the corresponding element at point H
(c)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
Question 8 Let z = g(x, y) = x³ + xy³ + y² - 6x - 2y + 4, where x = r cos (0) and y = r sin(0). Use the chain rule to find at (r, 0) =(√2, Z). Enter an integer or a fully reduced fraction such as -2, 7, -3/4, 41/7 etc.
None
3. Convert the decimal number 35710 into its hexadecimal number equivalent.
None
Q1: (20 marks) Write in summarat vou know abou fun me taleoems calculus. (20 marks) second
Respond with TRUE if the symbol of the valve shown below is drawn correctly Select one: True False
Q1: Write true or false a- The body is constant when no force effect of this. b- The moment is force x distance. c- Force is vector quantity. d- The force in the engineering dynamics is zero. e- Space is the geometric region for two coordinates and three coordinates. f- Particle is zero dimensions but have weight. g- Acceleration is a scaler quantity. h- We can use tan law to solve the problems. i- We use the plus in the cosine law when the angle between two force. j- Rivet between two plates is external force.
PLEASE ANSWER THIS USING YOUR OWN ANSWERS. DO NOT COPY ON INTERNET. IF YOU SEE THIS QUESTION AGAIN, DO NOT ANSWER. IF YOU ANSWER THIS IN TYPEWRITTEN, COMPLETE, CORRECT, AND IN ORIGINAL WAY, I WILL UPVOTE. THANK YOU!
Question 28 Not yet an If a particle is projected vertically upwards, it travels against gravitational force and hence the velocity of the particle will go on decreasing and velocity becomes zero, when it reaches the maximum height. Select one: O True O False hp
CHOOSE THE BEST ANSWER. SHOW THE DETAILS OF YOUR SOLUTIONS TO CREDIT THE CHOICE YOU MADE. DRAW THE FREE-BODY DIAGRAM CORRECTLY. (Refer to the image) 1. Which nearly gives the value of the angle beta in degrees? a. 60 degrees b. 62 degrees c. 65 degrees d. 58 degrees 2. Which nearly gives the value of the angle beta in degrees? a. 19 degrees b. 24 degrees c. 45 degrees d. 28 degrees