Figure Q3 shows a frame structure, which is fixed at A, D and F. The frame is subjected to the vertical load at the middle of span CE, uniform load along span BC and horizontal load at point E as shown in the figure. The relative plastic moments of resistance for all spans are shown in the figure. a) Identify the number of hinge and mode of failure mechanism in the frame structure (C01, PO1, C2) b) Based on your answer in (a), draw the mode of failure mechanism for the frame structure. (CO2, PO2, C3) c) Determine the maximum plastic moment for the frame structure (CO3, PO2, C4)

Figure Q3 shows a frame structure, which is fixed at A, D and F. The frame is subjected to the vertical load at the middle of span CE, uniform load along span BC and horizontal load at point E as shown in the figure. The relative plastic moments of resistance for all spans are shown in the figure. a) Identify the number of hinge and mode of failure mechanism in the frame structure (C01, PO1, C2) b) Based on your answer in (a), draw the mode of failure mechanism for the frame structure. (CO2, PO2, C3) c) Determine the maximum plastic moment for the frame structure (CO3, PO2, C4)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 01. The roof truss is loaded as shown in the figure. Determine the following; a) The support reaction at A Answer: b) The support reactions at F Answer: 500 N 500 N 500 N 400 N 600 250 N 250 N 'E 60° A 30° 30° 30° 5 m 5 m
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Figure Q3 shows a frame structure, which is fixed at A, D and F. The frame is subjected to the vertical load at the middle of span CE, uniform load along span BC and horizontal load at point E as shown in the figure. The relative plastic moments of resistance for all spans are shown in the figure. a) Identify the number of hinge and mode of failure mechanism in the frame structure (CO1, PO1, C2) b) Based on your answer in (a), draw the mode of failure mechanism for the frame structure. (CO2, PO2, C3) c) Determine the maximum plastic moment for the frame structure (CO3, PO2, C4) 2Mp 5kN/m 3Mp 5m C 2Mp Figure Q3 30KN 3Mp 8m E -10kN 2Mp 6m
A. diagram shows how the neutral surface of the structure changes shape under a given loading condition. Select the correct response: distributed load qualitative deflected shape bending moment shear
Q.2/The rigid beam shown in Figure 2 is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 10 mm downward, determine the normal strain developed in wires CE and BD. D 4 m P 2 2 m Figure 2 Rigid beam with wires and load
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
In 1, why if we separate the CD column, all the R1 force is in the column? But in 2, if we separate the CD column, half of the force F is in the column ... #structure_analysis
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 57 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 9 mm and the angle θ between the strut and the horizontal is 51°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 15 mm, the thickness of the gussets is tG = 12 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 12 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.
A steel strut S serving as a brace for a boat hoist transmits a compressive force P= 57 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 9 mm and the angle O between the strut and the horizontal is 30°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 16 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tg = 10 mm, and the diameter of the anchor bolts is dpolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa. ROUND OFF TO TWO DECIMAL PLACES. Pin S 16 (a) (b)
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA --- 120 mm 2.0 m INA = 30x105 mm What is the value of fleure stress in a distance 1.20 m from the free end at the topmost fiber of the beam section?
Truss members supporting a roof are connected to a 26-mm-thick gusset plate by an 18-mm diameter pin, as shown in the figure and photo. The two end plates on the truss members are each 14 mm thick. Disregard friction between the plates. Roof structure Truss member. P End plates Pin t = 14 mm Gusset plate 26 mm Truss members supporting a roof (a) If the load P = 60 kN, what is the largest bearing stress acting on the pin? (Enter the magnitude in MPa.) MPa (b) If the ultimate shear stress for the pin is 190 MPa, what force Pult is required to cause the pin to fail in shear? (Enter the magnitude in kN.) KN
es A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa -19.86 degrees Y -17.04 degrees -X Figure A Which of the following most nearly gives the principal planes for the combined state of stress? Select the correct response: 35 MPa 30° Figure B 30 MPa 30 MPa 4