Hi Please help me answer problem no.1 with drawing/figure. Thank you very much. Keep safe. FigureProblemIn the figure shown, determine the stress in thecable C if its area is 600 mm2. Neglect the weight1.Ccableof the bar AB.2 m.2m.2. In Problem 1, determine the required diameterthe pin at A if the allowable stress is 80 MPa.(double shear).Double shearВ600P= 30 kN

Answered: Image /qna-images/answer/65f17111-778a-4e54-a249-ebbaa086adc5.jpg

Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?. Neglect the weight of the bar AB. 1. cable 2 m. 2m. 2. In Problem 1, determine the required diameter of the pin at A if the allowable stress is 80 MPa. (double shear). Double shear B 60° P = 30 kN

Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?. Neglect the weight of the bar AB. 1. cable 2 m. 2m. 2. In Problem 1, determine the required diameter of the pin at A if the allowable stress is 80 MPa. (double shear). Double shear B 60° P = 30 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.10P: An aluminum tube has inside diameter dx= 50 mm, shear modulus of elasticity G = 27 GPa, v = 0.33,...

See similar textbooks

Related questions

Q: m= 800 kg, Cp=D0.2, A 2.2m2, Co-0.008, C-1x0.6x10-6 s/m, also take density of air p-1.18 kg/m' and a...

A: Given data-m=800kgCD=0.2Af=2.2m2g=9.81 m/s2Co=0.008C1=1×0.6×10-6 s2/m2ρ=1.18 kg/m3v(t)=0.29055t2 f...

Q: The cylinder bore diameter of a single-acting reciprocating pump is 150 mm and its stroke is 300 mm....

A: Write the expression of theoretical discharge of the pump. Qth=ALN60

Q: A 2-m long hollow steel shaft (G = 75 GPa) has an outside diameter of 75 mm and an inside diameter o...

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something. Technic...

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior micromet...

Q: Figure Q1 shows the angular velocity of rod AB at the instant is 15 rad/s clockwise, determine the a...

Q: yo 02 3 m 2 E Figure Q1 Determine the work space and the work envelope traced out by E for the simpl...

A: Given: the point O is fixed and we have to take positive angles in counterclockwise direction and ne...

Q: (sheet No.2) y water is transpor ted at 75°F (vz 10²$ for i500ft .in (lis)in -dianeter wrought iron ...

Q: 3. Determine the maximum deflection of the beam loaded as shown. Let Mo = 75 KN.m and L = 3 m. El is...

Q: B: The plate shown below is affected by the forces FA and FB, by assuming the value of 0, calculate ...

Q: In a game of pool, ball A is moving with a velocity vo of magnitude vo = 15 ft/s when it strikes bal...

A: Given condition Initial velocity of white ball = v0 = 15 ft/s

Q: AS STOWIT IIT the ske Delow, steam pipe of ue ulanmeter is Insulate u with d layer oI lum sincate. 1...

Q: he rear window of an automobile is defogged by passing warm air over its inner surface. If the warm ...

A: The heat flux through the window pane can be calculated using the formula given below as-

Q: A diesel cycle has a temperature after isentropic expansion of 100C. If expansion ratio is 4, find t...

Q: The pin support A and roller support B of the bridge truss are supported on concrete abutments. If t...

A: Given: Allowable bearing stress of the concrete, σa=2 ksi

Q: 1.) For the mechanism shown, determine: X mm a. Linear velocity of point B. b. Angular velocity of B...

Q: (Consider the stress tensor in a given point of a body): 2 1 Oij 2 0 2 1 2 0 (Determine o rag and id...

A: Stress is a force per unit area and its SI unit is N. Null vector is defined as a vector of zero val...

Q: Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible. ...

A: Given Specimen To find Stress vs strain diagram Modulus of elasticity Modulus of resilience Yield st...

Q: Q5: For the below shaded area, calculate Ixand Kx 130 mm 30 mm 30 mm mmt- 40 mn -40

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

Q: Air at 30 deg. Celsius and 110KPa flows at 20N/s through a rectangular duct that measures 160mm x 32...

Q: 8.1 Find the total delta-v required for a Hohmann transfer from earth's orbit to Saturn's orbit. [An...

A: To Determine The total delta-v required for a Hohmann transfer from earth's orbit to saturn orbit. ...

Q: For the truss shown below, use symmetry to determine the displacement of the and the stresses in eac...

Q: 1. A train weighing 100 tons is being pulled up a 2% grade. The train resistance is constant at 10 I...

Q: • A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, an...

Q: A linear thermal actuator is being used, inside it contains wax with a specific volume of 15%, that ...

A: Gievn Data The specific volume is: v=15% The expansion of the wax is: 15% The required stroke lengt...

Q: 5/42 A variable-speed belt drive consists of the two pulleys, each of which is constructed of two co...

Q: Two parallel shafts, 27 inches apart and having a speed ratio of 2.6 are connected by cylinders in p...

Q: Q1: Choose the correct letter (a, b or c) (Only the letter)_ (for FIVE Only) 1- The .. . is a repres...

Q: Explain the difference between the microscopic and the macroscopic forms of energy. State the approa...

Q: alculate the reactions at the point O

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform angu...

Q: 4- When the car is slowing down, that means it is a) accelerating b) decelerating 5- We can say that...

Q: An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm ...

Q: 16. Find the rectangular equation of a curve whose parametric equations are x = 2 cos 0, y = 2 sin 0...

Q: The pressure difference between point A and point B is to be measured using an inclined mercury (SG ...

A: GivenSG=13.6θ=15oL=4.8cm

Q: A sphere is fired downwards into a medium with an initial speed of 27 m/sec . If it experiences a de...

A: Given Velocity, u = 27 m/s Deceleration, a = - 6t m/s2 Find Distance travelled

Q: Thex- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the c...

A: Given ,X=25+0.78t^2 Differentiating both sides w.r.t time , Vx=1.56t at t=1.6s Vx=2.496mm/s

Q: 24) The Young's modulus and the shear modulus of material are 120GPa and 45GPA respectively. What is...

A: From the given data, Young's modulus = E = 120 GPa Shear modulus = G = 45 GPa Let us represent, Bu...

Q: Consider a boiler that burns sub-bituminous coal. The boiler has a cyclone furnace burner and has a ...

A: Given : P = 500 MW C = 25 MJ/kg To find : Annual emissions of mercury

Q: 7kN m 5 kN/m |C B D = 3m to D/2 D/2 12KN

Q: A boiler produces 5000kPa steam which is 67% dry, from boiler feed water @ 100°C. flow rate is 960 k...

Q: The discharge pressure of an air compressor is 8 times the suction pressure. If volume flow at sucti...

Q: How are porous bearings made and where are they used?

A: Introduction: porous bearings are made of by the process of powder metallurgy. porous material mainl...

Q: A centrifuge bowl is to separate two immiscible liquids, one with SG 1.1 and the other with SG 0.9. ...

Q: 24) The Young's modulus and the shear modulus of material are 120GPa and 45GPA respectively. What is...

A: From the data given in question, Young's modulus = E = 120 GPa Shear modulus = G = 45 GPa Let us d...

Q: (a) q=20 kN/m M=20 kN-m C B D 1 m 1 m 1m FB .

Q: Sketch the power density distribution for oxyfuel gas welding and GMAW process.

A: Fusion welding processes are analyzed using the power density that they can supply to melt the surfa...

Q: A company has 237 employees. Of these, 205 participate in at least one of the company's two payroll ...

Q: The flat surface shown is submerged vertically in water. Find the fluid force against the surface. T...

Q: 3 2i (i – 1) + (V3 – 1)° + (1+ i) (1 – ) - |

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

Hi Please help me answer problem no.1 with drawing/figure. Thank you very much. Keep safe.

Figure
Problem
In the figure shown, determine the stress in the
cable C if its area is 600 mm2. Neglect the weight
1.
C
cable
of the bar AB.
2 m.
2m.
2. In Problem 1, determine the required diameter
the pin at A if the allowable stress is 80 MPa.
(double shear).
Double shear
В
600
P= 30 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by the distance b = ISO mm from the line of action of the weight force W. The allowable stresses in the arms are 100 MPa in tension and 50 MPa in shear. If the loaded gondola weighs 12 kN, what is the minimum diameter roof the arms?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F = 72 kN (see figure). The cylinder has diameter d = 100 mm and wall thickness t = 4 mm. Calculate the maximum allowable internal pressure /?max based upon an allowable shear stress in the wall of the tank of 60 MPa.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.