Figure L 30° VA 2m 10 m- 1 of 1 3 m Part B Determine the magnitude of the basketball's velocity when it passes through the basket. Express your answer to three significant figures and include the appropriate units. VB = Submit ▾ Part C 0 = μA Submit Value Request Answer Determine the angle at which it passes through the basket. Express your answer in degrees using three significant figures. VAΣ vec Units Request Answer ? www. ? °, measured clockwise from the positive a axis

Q: Define external force system.

A: Forces that are present in nature can be categorized into a different section in various ways. One…

Q: Define Locked in loads

A: Load  - A load is a mechanical stress , moment or couple that a mechanical body is subjected to…

Q: Q2.Write Types of Key and Explain in detail with Diagram.

A: key A key is a machine element which is used in between shaft and hub or Boss of the pulley to…

Q: What is the force output of a cylinder that has a 1” bore and operated at 600 psig?

A:

Q: 3 50mm link is fixed, the number of finks can rotate fuy filly that

A: Given data: Let 4 links;s=100 mmp=200mmq=300mml=350mmas shown in fig. if 350 mm is fixed  then  no.…

Q: Write short note on compression ratio

A: compression ratio

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: Distinguish nominal diameter and gross diameter of bolt

A: Nominal diameter:Nominal diamater can be described as the pitch diameter of the thread of the…

Q: To prevent a manual-type torch from damage, it is madeof a special plastic that resists what?

A: The plasma torch is a device that allows the creation and control of the plasma for welding or…

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

A:

Q: The three friction disks shown are made of the same material and have the same thickness. It is…

A: The number of revolutions required.Given:The weight of the disk A is .The radii of the disks are…

Q: An example of a performance with two phases is the bench press; in the down phase the lifter lowers…

A: The preparation phase and the movement phase of the bench press exercise can be separated.…

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: 13. When tightened, dry seal threads A. are crushed to make a leakproof seal. O B. compress an…

A: According to t the question We need to explain the problem  13,14 and 15

Q: Removable joints can be made by using welding. Select one:

A: This statement is (FALSE)

Q: True/false Q-5 Specific weight is an extensive property? If yes why ?

A: Specific weight is define as tge ratio of weight of the substance to its volume.  w• = W/v  W = mg {…

Q: Generally, the Poisson's ratio of steel is

A: Poisson ratio of steel = 0.3 Option (c) is correct.

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: Define and explain hookes law

A:

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: The rotation angle of the joints is still needed.

A:

Q: Question 2: How long a wrench is needed to tighten a 9/16-inch bolt if the maximum force (pull) that…

A: Given: The diameter of bolt, d = 9/16 in = 0.5625 in The maximum force produced by mechanic, F = 75…

Q: True or False? The largest diameter threaded rod is available only up-to 8-inches

A: The threaded rod has several different measurements associated with it. There is major diameter,…

Q: Materials that can be used as housing for the Wedge belt Drive

A: The materials used are -

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: Which of the following statements pertaining to the steel tubing is not true: Steel tubes are…

A: Given: Steel tubes are better than steel pipes because, they:   are less expensive.…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: A pocket milled in the base of part A. Design of ared which will articulatewith part Band which will…

A: To mill a pocket in part A(base) , one should be aware of the process of the pocket milling. Pocket…

Q: List some factors of safety for design of drilled shafts.

A: A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled…

Q: how did you get the 3038Pa in static pressure?

A:

Q: False

A: It is False. Higher the gauge number, indicates thinner the sheet metal.

Q: specific weight is also known as weight. select one: True False

A: Answer: False

Q: What are the concerns about dropping an item using a chain in place of a rope?

A: Both the chain drive and belt drives have a separate application, belt, and rope drives will be used…

Q: What is meant when a metal is said to have goodweldability?

A: Weldability describes the ease with which a metal can be welded properly. The weldability of any…

Q: What is the point called when a material fractures?

A: The point at which material fractures is called the point of fracture or fracture point. In other…

Q: How to find the diffliction of the string at any point

A:

Q: Helical gear

A: Ans is Helical gear

Q: A kick occurs because the pressure inside the wellbore annulus is higher than formation pressure. a.…

A: The kick formation depend on the pressure gradient in wellbore annulus and formation pressure.

Q: can you show a clear sloution

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.