Figure40 kN/m15m-1 of 1If the allowable beaning stress for the matenal under the supports at A and Bis 14 MPa, determine the size ofsquare bearing plates A' and I required to support the load. Dimension the plates to the nearest mm. The reactions at thesupports are vertical Take P= 120 KN(Eloun1)Enter your answers separated by a commaVALOItvec?10714,117857.14Submit Previous Antwers BequestAnswer* Incorrect, Try Again; 5 attempts remaining4man

Given:- The allowable bending stress at A and B = σallow = 1.4 MPa The magnitude of the uniform load…

Figure (101) the allowable bearing stress for the maternal under the supports at A and B 14MPa, determine the son of square bearing plates A and B required to support the load Dimension the plates to the nearest mum. The supports are vertical Take P-120 KN afte (Exu) Enter your answers separated by a comma VAXtve 4 A 7 10714,117857.14 Submit A Bevest X Incorrest Try Again; 5 attempts remaining

Figure (101) the allowable bearing stress for the maternal under the supports at A and B 14MPa, determine the son of square bearing plates A and B required to support the load Dimension the plates to the nearest mum. The supports are vertical Take P-120 KN afte (Exu) Enter your answers separated by a comma VAXtve 4 A 7 10714,117857.14 Submit A Bevest X Incorrest Try Again; 5 attempts remaining

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
Ana ly ze the sta tic a lly in d e te rm in a te be am shown by the d is trib u tio n m e th od. D raw shear and bending -moment diagrams. Ske tch of th e de fo rm e d structure notneeded. moment- P 12 ft 28 ft A A В 3 lc 2 lc 3 lc 40 ft 20 ft 4 0ft P(k) w (k/ft) 43.8 3.0
回の shear stress tmax in any of the three bars? P3 9 m P 135° up. (D 135° 90 dz s applied Knowing the steel the steel 09. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. s in the (a) If the inner radius of the tube is r, = 40 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1 (in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0005 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2)max? B 12 mm is to be of ACR
2. Determine the reactions in the supports and draw the shear diagram. siatb mSTgcib 18ode orlt mi soTA 2 k/ft 75 k A Ja IP . -15 ft--15 ft- 30 ft- n oinbim to a ebim oris i BOTA+S 31 E = constant + 0001) t di 8T.00.
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.
20kN/m P2=70 EN A=70° 1,5m um Im 1- Find the support reactions of the simple beam 2- Fnd internal equatrons and values force 3- Plot N vM draerams and elastic curve 7 moment L- Pind the location and value of max and Mn Moments
RBH TRBV 3. The frame shown in the figure is hinged to rigid supports at A and E. find the components of the hinge forces at A and E and the forces in members BC and BD. RAH A REH TRAV E REV 120 D 5 0 ction
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
(2) sz The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to aload of 75 kN at D. the relation between the movement of point N BtoDis TSN 36B =2 8D 26B =3 6D 8B =4 6D None of all these 26B = 8D O OOO0O0
E oth ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T must e applied so that the reactive torques at A and B are equal. 2 0.75d B T a A.
F14-11. Determine the principal stresses at point A on the cross section of the beam at section a-a. -300 mm- IT 150 mm S0 mm 30 kN 30 mm
Eiample ai ABC is loaded via a 500 N.m couple and a 600 N force as shown. Tlie The is connected to the rest of the system by a pin joint at B and a roller support at Beteune the magnitide of the reaction forces on the beam at the supports. 600 N 300 N m 400 300 500 Ans. Dimensions in mm RC=1700 N 20 RBx=1597.5 N RBy=1181.4 N Erample Determine the force Pnecded to lift the load. Alsa, determine the proper placement x of the hook for cotilibrium. Neglect the weight of the beam. 0.9 m 100 mm 100 mm 100 mm 6 kN The uniform rod of length L and weight W is supported on the simooth planes. Determine its position e for equilibrium. Neglect the thickness of the rod. Ans 6= tan