Figure 1 shows schematically the arrangement of a drilling machine. Following are the sequence of operation 1. The operationis to be started using a push button to extend clamping cylinder Ml completely before vertical cylinder M2 extends. 2. Cylinder M2 extends and perform the drilling operation after 10 seconds of clamping. 3. Consecutively, the vertical cylinder M2 extends and retracts much more quickly than the clamping cylinder M1 (about twice as fast). repeat this operation for 10 such workpieces. design the following a) Design the hydraulic circuit for drilling the workpiece with proper electro-hydraulic components| b) Design the Electrical Circuit for the above-mentioned sequence. c) Draw the function diagram for the designed system. -$2.1 -M2 -$2.20 -S1.1 -S1.2 -M1 Figure 1 Drilling a workpiece

Figure 1 shows schematically the arrangement of a drilling machine. Following are the sequence of operation 1. The operationis to be started using a push button to extend clamping cylinder Ml completely before vertical cylinder M2 extends. 2. Cylinder M2 extends and perform the drilling operation after 10 seconds of clamping. 3. Consecutively, the vertical cylinder M2 extends and retracts much more quickly than the clamping cylinder M1 (about twice as fast). repeat this operation for 10 such workpieces. design the following a) Design the hydraulic circuit for drilling the workpiece with proper electro-hydraulic components| b) Design the Electrical Circuit for the above-mentioned sequence. c) Draw the function diagram for the designed system. -$2.1 -M2 -$2.20 -S1.1 -S1.2 -M1 Figure 1 Drilling a workpiece

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing
A gear box contains 3 sizes of gears, 8 tooth, 32 tooth and 64 teeth. The 8 tooth gear is driving the 64 tooth gear and is turning 48 turns/second - how fast is the 64 tooth gear turning?
In CNC lathe machine, the G02 code is referred for O a. Drilling cycle b. Zero offset O c. Contour Turning Cycle d. Circular Interpolation Clockwise
Which of the following commands will move the tool in a diagonal line at a feed rate of 5 from position (10, 20), assuming absolute programming mode is active? Select one: a. N10G00X10F5 b. N10G01X20Y30F5 c. N10G01X10F5 d. N10G00X20Y30F5
If there is at least one gear axis rotates around the other axis, the gear train is ordinary gear train. please quickly true or false
im sorry for the inconvinience , 500 d/d means 500 rpm. Its translated from turkish textbook , i forgot to translate the rpm value. Could you correct the substitutions please ?
Fill in the data needed in the table RPM FEED LENGTH OF CUT CUTTING TIME 325 0.006 6. 6 1/8 74 0.010 2 7/8 130 0.008 1 1/2
10q In down milling, the workpiece is feed against the rotation of the milling cutter to produce a flat surface. Select one: True False
Write a complete part program using canned cycles to produce the drilled hole, groove, and thread on the workpiece that is shown in figure with Fanue syntax. You may assume that the OD (Outside Diameter) and chamfer are already finished. Use the following parameters: Material: 1018 steel Tool: Ф0.25 HSS drill, T0101 60° carbide threading tool, T0202 0.125 carbide grooving tool, T0303 Cutting speed: 300 SFPM for carbide and 100 SFPM for HSS tools. Use constant surface speed where appropriate Feed: 0.005 IPR (except for thread)
# Teeth on gear Pinion RPM # Teeth on pinion Gear RPM 60 X 90 270 Using the information from the chart in question 6 above answer the following. What is the ratio of the gear rpm to the pinion rpm in its lowest terms?
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
Please don't provide handwritten solution ...