Explain vadose zone?
Q: What is adsorption zone?
A: The deposition of molecular species onto the surface of any object is known as adsorption. The…
Q: Explain critical failure plane ?
A: Brief Concept- Critical failure plane- It is related to the soil mechanics subject and the shear…
Q: 1. The figure below shows a sample loop traverse with the unadjusted field data. For letters a, b,…
A:
Q: Define the term capillary fringe.
A: The capillary fringe is characterized as the saturated zone of water immediately just above the…
Q: True or False ? A slum is a very clean place it is true or false
A: Slum- * It may be defined as the part of a town, usually located in urban areas, where lack of good…
Q: Q5-) Explain the standard consistency Procedure? according to the guide manual No. 1042@2011.
A: The standard consistency of a cement paste is outlined as that consistency which is able to allow…
Q: What is a multi-tube cyclone or multicone?
A: Air pollution is the addition of pollutants in the atmosphere which degrades the quality of air and…
Q: Determine the reactions at A and C; Determine forces at members FE, CE, and CD using Methods of…
A:
Q: What is susbtainable design?
A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…
Q: What is internal erosion?
A: Internal erosion can be defined as it is the development of voids inside the soil, which is caused…
Q: xamples of internal and exterior fragmentation are shown. Make use of visual aid
A:
Q: verity of seismic forces.
A: The sudden release of energy from the Earth's crust leading to production of waves which cause…
Q: Explain pipe earthing
A: Brief concept- Earthing- It is a process by which charge is transferred to the earth with the help…
Q: PROBLEM 1: A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats…
A:
Q: ***** For the shown forces, the coordinate direction angle (a) for the resultant force equals.. You…
A: We resolve all the loads along x y and z axes α is the direction cosine of resultant force R with…
Q: n angle of 2 346° respec e of the new ec" new curve.
A: SOLUTION OF QESTION NUMBER 6 BELOW
Q: What is shear starin rate?
A: Shear rate:
Q: 2. Determine the force in each member of the truss shown. State whether each member is in tension or…
A: To determine the force in all the members of truss-
Q: A single row of sheet piles is driven into a permeable layer as shown in the figure. Giyert H = 5.5…
A: Given data, H1 = 5.5 m H2 = 4.4 m Nf = 4 Nd = 8 k = 4 x 10^-4 cm/s To find out the seepage loss…
Q: prevent a load (weight W) from falling downwards. The drum can rotate without friction about point…
A:
Q: Define what is Inclinometer ? Explain the use of Inclinometer ?
A: Inclinometer- It is a device or sensor used to measure the inclination angle of any bent structure.…
Q: 2) Find the maximum deflection (including its location), and the maximum slope (including its…
A:
Q: A 1-m wide curved gate supports water as shown. The gate is from a sector with radius 6 m and…
A: Width of gate (w) = 1 m area of sector = 60 ° radius of sector (R) = 6 m compute: a. vertical force…
Q: What is ASD method
A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…
Q: What purpose does a sealant backup rod serve?
A: sealant is a substance used to block the passage of fluids through the surface or joints or openings…
Q: ituation 4: Three layers of soil are shown with the corresponding values of coefficient of…
A: Q. 7 & 8 has some missing data or content. But Q. 9 & 10 can be answered from the given…
Q: SIT 12. For the given figure below. El=constant 20 KN A 21 2m 2 m BI 4.5 m 25 KN/m Į Į 77 CI a.…
A:
Q: a. Compute the critical buckling stress (Fcr in MPa). b. Compute the nominal compressive strength of…
A:
Q: How does the Information on surface conditions necessary for planning construction techniques?
A: Information on surface conditions is very much necessary for planning construction techniques is…
Q: Explain isobar?
A: An isobar is a contour or curve showing all the points below the earth's surface having equal…
Q: How are finished grades determined in machine guidance and control?
A: .Today’s machine-control systems help operators of all skill levels get to finished grade faster by…
Q: Bolted Connections hear lap connection
A: Single Shear Lap Connection: 22 mm bolts Fnv = 300 MPa Bolts are in Single Shear Number of bolts = 6…
Q: Define the term Underabsorption of Over-Head?
A: Let’s first understand the definition of overhead: Overhead refers to the continuing business…
Q: Techniques
A: The single sideband technique is a technique which is used for transmitting information like an…
Q: What is the vadose zone, capillary fringe zone, and phreatic zone
A: Groundwater:- Water that is underground and can be found in voids and cracks in sand, rock, and…
Q: Distinguish between skewerness and dispersion?
A: Brief concept introduction- skewerness and dispersion- These two terms are very important in the…
Q: Explain what is slurry-trench.
A: Slurry trenches are the walls which are cut – off type and these are used to control the gases and…
Q: A square column foundation has to carry a gross allowable load of 1605 kN (FS = 3). Given: Dj = 1.7…
A: To Find :- size of foundation B
Q: 6. In the manometer shown at right, containing mercury (s.g.-13.6) from A to B, and oil (s.g.=0.85)…
A: Given Data Determined the pressure at point C.
Explain vadose zone?
Step by step
Solved in 2 steps with 1 images
