Expectation: For the two bus power system shown below. Assume that bus one is the slack and S Base = 100 MVA. One Line Z = 0.1j 1.000 pu OMW 0 MVR Two 1.000 pu 200 MW 100 MVR 1. Using Newton-Raphson power flow method to determine the voltage magnitude and angle bus two; 2. Using dishonest Newton power flow method to solve same problem; 3. Using Decoupled Newton-Raphson method to solve same problem; 4. Using Fast Decoupled Newton-Raphson method to solve the same problem; 5. Using DC power flow to solve the same problem.

Expectation: For the two bus power system shown below. Assume that bus one is the slack and S Base = 100 MVA. One Line Z = 0.1j 1.000 pu OMW 0 MVR Two 1.000 pu 200 MW 100 MVR 1. Using Newton-Raphson power flow method to determine the voltage magnitude and angle bus two; 2. Using dishonest Newton power flow method to solve same problem; 3. Using Decoupled Newton-Raphson method to solve same problem; 4. Using Fast Decoupled Newton-Raphson method to solve the same problem; 5. Using DC power flow to solve the same problem.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.43P

See similar textbooks

Similar questions

1. FIGURE 52 shows the one-line diagram of a simple three-bus power system with generation at bus I. The voltage at bus l is V1 = 1.0L0° per unit. The scheduled loads on buses 2 and 3 are marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. For the purpose of hand calculations, line resistances and line charging susceptances are neglected a) Using Gauss-Seidel method and initial estimates of Va 0)-1.0+)0 and V o)- ( 1.0 +j0, determine V2 and V3. Perform two iterations (b) If after several iterations the bus voltages converge to V20.90-j0.10 pu 0.95-70.05 pu determine the line flows and line losses and the slack bus real and reactive power. 2 400 MW 320 Mvar Slack 0.0125 0.05 300 MW 270 Mvar FIGURE 52
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)
please solve for nodal stress method. (if it is possible to apply supernodes)
Q6/ The per-unit reactance for a given system are shown in figure below. (1 MVA) is being delivered to the receiving end bus of the system at unity power factor and unit voltage. A three phase short circuit occurs at F. Find the critical clearing angle and the critical clearing time? Take H = 3 p. u. second tc X=j0.3 j0.1 w Peralat j0.25 j0.25 V20 x 1
Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUs and find V₂ and 62, power flows and line losses using FDLF method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch. 1 Z12= 0.12+10.16 Slack bus V₁ 1.0/0⁰ pu 2 PL2=1.0pu Q12=0.5pu
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
Figure below shows one-line diagram of a simple three bus power system with generation at bus 1. Bus 1 is considered as slack bus. A load consisting of 250 MW and 110 MVAR is taken from bus 2. A load consisting of 128 MW and 35 MVAR is taken from bus 3. Line impedances are marked in per unit on a 100 MVA base. Line susceptances are neglected. G1 0.01 +10.03 V₁ = 1.040° 0.02 +0.04 Select one: O a. None of these O b. 0.9245-j0.025 O c. 0.9245+j0.025 O d. -0.9245-j0.025 e. 0.9638-j0.03 0.0125+j0.025 ·0 P2 Q2 P3 Q3 Start with flat initial estimates of ₂0) = 1 + j0 & V3⁰) = 1 + j0, and keeping |V₂| = 1 pu, find V₂(¹)
Solve numerical : Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUS and find V2 and δ2, power flows and line losses by using Fast decoupled power flow method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch.
A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the lines interconnecting the buses are as follows: X12 = 0.1pu, X13 = 0.12 pu and X23 = 0.2 pu. There is a generator at each bus. The loads at buses 1, 2 and 3 are 150MW, 200mw, and 100MWrespectively. Bus 1 is taken as the reference bus, and SBase = 100 MVA. Which one of the below is a constraint of the DCOPF problem? Select one: O a. None of these O b. -500 0₂-1000 03 = P3 - 110 O c. 1500 0₂-500 03 = P₂ - 220 O d. 1500 0₂-500 03 = P₂ - 200 O e. -500 0₂-1000 03 = P3 - 150 O f. -1500 8₁-1000 03 = P₁ - 150
Figure shows the one-line diagram of a simple three-bus power system with generation at buses 1 and 3. The voltage at bus 1 is V1 is 1.025 at an angle of 0◦ per unit. Voltage magnitude at bus 3 is fixed at 1.03 pu with a real power generation of 300 MW. A load consisting of 400 MW and 200 MVAr is taken from bus 2. Line impedances are marked in per unit on a 100 MVA base. (a) Construct Ybus matrix for the system in Figure (b) Using Gauss-Seidel method and initial estimate of V2(0) = 1.0 + j0 and V3(0) = 1.03 + j0 and keeping |V3| = 1.03 pu, determine the phasor values of V2 and V3. Perform two iterations.