EXERCISES3.10 Show that if N, > Np.Is AqnN3.11 For the pn junction in Example 3.6, find the value of I, and that of the current / at V 0.605 V (samevoltage found in Example 3.6 at a current /-0.1 mA) if N, is reduced by a factor of 2.Ans. 1.46 x 10" A; 0.2 mA3.12 For the pn junetion considered in Examples 3.5 and 3.6, find the width of the depletion region W cor-responding to the forward-bias voltage found in Example 3.6. (Hint: Use the fomula in Eq. (3.31)with replaced with -Vg.)Ans. 0.166 um3.13 For the pn junction considered in Examples 3.5 and 3.6, find the width of the depletion region W andthe charge stored in the depletion region Q, when a 2-V reverse bias is applied. Also find the valueof the reverse current I.Ans. 0.608 um; 9.63 pC: 7.3 x 1015 A

Bartleby has policy to solve only first question and incase if it has subparts then solve only first…

Answered: EXERCISES 3.10 Show that if N, > Np. D.…

Engineering

Electrical Engineering

EXERCISES 3.10 Show that if N, > Np. D. - Aqni LN Is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
3Q1:For the circuit on the right,a. Graph the output voltage v0 against the input voltage v1.Assume ideal diodes.b. Describe the behaviour of D1 in terms ofsemiconductor behaviour.Q2: For the circuit shown in Figure 1:1. Describe the behaviour of a p-n junction in terms of semiconductor behaviour.2. Describe and evaluate the circuit. Assume the values for the parameters in the circuit.You should critically evaluate the performance of the circuit and suggest potential applications.Q3: For the circuit shown in Figure 2, find the following:1. Describe the function of the circuit in terms of simple of semiconductor behavior.2. Evaluate the output voltage vo, assuming vs is 10 Sine (200t) mV, RE1 =100 Ω,and RE2 =900 Ω. The bypass capacitor (CE) is in parallel with RE2.3. Simulate the circuit and verify your answers; you should show the input voltage.and output voltage on the same graph.4. You should explain the characteristics of the amplifier.
Which of the following options is FALSE about the semiconductor diodes? Lütfen birini seçin: O A. Diodes are made of semiconductor materials with additional dopping to enhance their conducting properties. O B. They are non-linear devices; hence, if one wants to draw their current-voltage graph, they will end up with an exponential plot. O C. The type of the semiconductor material matters in the characteristics of the device; such that the forward-bias voltage (Vp.) is different for Ge and Si based diodes. O D. They ideally let the electric current flow in the direction from cathode terminal to anode terminal, while completely blocking it in the direction from anode to cathode.
Derive the expressions for current-voltage I -V relation, short circuit current ISC, and open circuit voltage VOC of a p-n junction solar cell.
For intrinsic semiconductors, the concentration of intrinsic carriers ni depends on the temperature of theas follows:Thus, a graph of (ln ni) as a function of 1 / T (K) –1 must be linear and have a slope of (-Ee / 2k). Explain,succinctly, the reason for the presence of factor 2 in the denominator of Equation 1.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A zener diode of voltage Vz( 6 volt) is used to maintain a constant voltage across a load resistance RL( = 10000) by using a series resistance Rs(+1000). If the emf or source is E( = 9V), calculate the value of current through series resistance, zener diode and load resistance. =
The carrier concentrations (Figure 1) are approximations for the case where the net (n-type or p-type) doping of the semiconductor is very well defined (>> ni ). For generic semiconductor doping, the relations in Figure 2 take effect. Deduce the relations from Figure 2. Please explain each step as I'm having trouble in understanding this subject. P.S.: I sent this question before and the signals in Nd and Na came out wrong. Please be aware!
An intrinsic semiconductor is neither a good conductor nor a good insulator. Select one: O True O False A varactor is a pn junction diode that always operates in reverse-bias and is doped to maximize the inherent capacitance of the depletion region. Select one: O True O False A simple diode rectifier has 'ripples' in the output wave which makes it unsuitable as a DC source. To overcor this on e can use
Design a Zener diode circuit to regulate a source voltage that can vary from 9 VDC to 17 VDC, has a load current that can vary from 0 mA to 500 mA to generate a constant load voltage of 5 VDC. Draw the complete circuit with all values, determine the largest value of the inline source resistance (Rs), and determine the Zener diode's max power dissipated. Pzmax = Rsmax =
A silicon pn junction at zero bias has dopant concentration of N₁ = 3 x 10¹7cm-³ and Nd= 4 x 10¹6 cm3 at T=300 K. Assume Vbt = 0.77 V. C. Draw the curve of electric field of this junction; showing the most important points.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)