EXepe 6 For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s. Damping is 10% of critical, Cross-sectional dimension of each column is 250 mm x 300 mm and elastic modulus is 22.8 GPa. Determine (a) () (c) the natural frequency (rad/s) the amplitude the expression for the displacement 500 kN ... 3 m 5 m

EXepe 6 For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s. Damping is 10% of critical, Cross-sectional dimension of each column is 250 mm x 300 mm and elastic modulus is 22.8 GPa. Determine (a) () (c) the natural frequency (rad/s) the amplitude the expression for the displacement 500 kN ... 3 m 5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

16. The formula of axial deformation PL/(AE) is applicable only if the cross-section of the material is uniform. True False 17. In the formula of torsional stress, "G" is called modulus of rigidity. True False 18. In the formula of torsional stress, "J" is called moment of inertia. True False
1. An aluminum tube AB of circular cross section has a guided supporter at the base and is pinned at the top to a horizontal beam, which supports a load of Q=200 kN as shown in the accompanying illustration. If the outside diameter of the tube is d=200 mm, determine the required thickness, t, of the tube. Use Euler's buckling theory, and assume a safety factor of N=3. (N.B.: For the aluminum used for the column, use E = 72 GPa.) -1.0 1.0 m B THI 1.0 m- Jº= d = 200 mm 200 KN 2.0 m
е Q2). A 20m steel tape supported at both ends was used to measure horizontal P distance of CD at a temperature of 35 °C and 60 N tension force measured distance was 350m. Under the standard conditions was found that the tape 19.95m length. Find the actual horizontal distance between CD if: Ts Standard temperature 25 °C Coefficient of thermal expansion of steel tape = 11.6x10-6/°C Po Standard tension = 100N. Modulus of elasticity (E) = 210 kN/mm² Cross-sectional area of the tape = 2 mm² The weight of this tape between supports 8 N
Thanks for answering
Plz solve
A STEEK ROD HAVING A CROSS SECTIONAL AREA OF 560mm2 IS SUSPENDED VERTICALLY IN ONE END. IT SUPPORTS A TENSILE LOAD OF 15KN AT THE LOWER END.
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN, as shown in the figure. 4000 L1-400 mm + L2- 900 mm 1 1 41-100 mm² EI=2×10 MPa 42=60 mm² E2-3x105 MPa P-1 kN Segments 1 and 2 have cross-sectional are of 100mm² and 60mm², Young's modulus of 2x10³ MPa and 3×10³ MPa, and length of 400mm and 900mm, respectively. The strain energy (in N-mm, up to one decimal place) in the bar due to the axial load is
B2
The column is subjected to an axial force of 8 kN, which is applied through the centroid of the cross-sectional area. Determine the average normal stress acting at section a-a. Show this distribution of stress acting over the area’s cross section.
bending moment changes sign shear force is maximum iii. bending moment is maximum GROUP-B 1) Derive the relationship between Young's modulus (E) and Bulk Modulus (K). 2) For the aluminium shaft shown (G = 27 GPa) below, (a) determine the torque T that causes an angle of twist of 4°, (b) the angle of twist caused by the same torque T in a solid cylindrical shaft of the same length and cross-sectional area. 1.25 m 18 mm 12 mm
number of significant digits; the tolerance is +_1 in the third significant digit