AEx 5.5 solution.pdf - Adobe Acrobat Reader DC (32-bit)Dosya Düzenle Görünüm įmzalama Pencere YardımEx5.1 s.Ex5.5 s.. xEx5.6 s.Ex5.7 s.Ex5.8 s...E>Ana SayfaAraçlarPowerP.PowerP..図Q1 / 2Example 5.5(chp5ex5)A three-phase, 60-Hz, 500-kV transmission line is 300 km long. The line induc-tance is 0.97 mH/km per phase and its capacitance is 0.0115 uF/km per phase.Assume a lossless line.(a) Determine the line phase constant 3, the surge impedance Ze, velocity of prop-agation v and the line wavelength A.(b) The receiving end rated load is 800 MW, 0.8 power factor lagging at 500 kV.Determine the sending end quantities and the voltage regulation.

Transmission lines are used to transfer power from the generating station to the distribution…

Example 5.5 (chp5ex5) A three-phase, 60-Hz, 500-kV transmission line is 300 km long. The line induc- tance is 0.97 mH/km per phase and its capacitance is 0.0115 F/km per phase. Assume a lossless line. (a) Determine the line phase constant 3, the surge impedance Zc, velocity of prop- agation v and the line wavelength A. (b) The receiving end rated load is 800 MW, 0.8 power factor lagging at 500 kV. Determine the sending end quantities and the voltage regulation.

Example 5.5 (chp5ex5) A three-phase, 60-Hz, 500-kV transmission line is 300 km long. The line induc- tance is 0.97 mH/km per phase and its capacitance is 0.0115 F/km per phase. Assume a lossless line. (a) Determine the line phase constant 3, the surge impedance Zc, velocity of prop- agation v and the line wavelength A. (b) The receiving end rated load is 800 MW, 0.8 power factor lagging at 500 kV. Determine the sending end quantities and the voltage regulation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the sum of series of odd numbers from the list of numbers. The length of the list is in ML 2200H and series itself begins from ML 2201H. Assume the sum to be greater than FFH. Store the results in ML 2300H and 2301H in 8051 microcontroller.
Chapter # 3 Integrated Circuit Technologies Q. Use Table below to explain why the circuit of Figure below will not work as it is. How can the problem be corrected? HW # 04 74нсо 7402 B 7402 Y. Input/output currents for standard devices with a supply voltage of 5 V. CMOS TTL Parameter 4000B 74HC/HCT 74AC/ACT 74AHC/AHCT 74 74LS 74AS 74ALS 74F hulmax) 1 HA 1 HA 1 A 1 µA 40 A 20 A 20 μΑ 20 HA 20 uA AL(max) loH(max) lo(max) 1 A 1 uA 8 mA 1 A 100 A 0.6 mA 1 LA 24 mA 1.6 mA 0.4 mA 0.5 mA 0.4 mA 4 mA 0.4 mA 0.4 mA 2 mA 400 mA 1.0 mA 0.4 mA 4 mA 24 mA 8 mA 16 mA 8 mA 20 mA 8 mA 20 mA Electriai Engeg bepatnt verity f ara
A 12-bit ADC unit has an input voltage range of -ve 5to +ve 5 VDC. What is the minimum difference in voltage required by an analogue signal for the digitally converted value to reflect that change(resolution)? 0.0012V DC b. None of all 0.083V DC C. 0.0024V DC 4
For the cct shown below find zt and drow the equivalent cct IPD I Cgdp RE Cgdn CPD VDD Mp Ma HH Figure 5. Schematic diagram of the Inv-TIA. Cout
Problem 15. We are comparing to COTS ADCS (Commercial Off-The-Shelf Analog to Digital Converters). Unit A is a 10-bit ADC with ENOB = 8.6 bits. Unit B is a 10- bit ADC with ENOB = 8.8 bits. Which unit has better SINAD? a. Both units have Same SINAD b. Unit A c. Unit B d. Not enough information e. N/A
logic circuitjust draw the graph
In a simple, three-phase voltage-source inverter of the form shown in Fig. 8.18, the direct voltage va in the link is 550 V. The frequency of the inverter output is 200 Hz. Determine: (a) the rms value of the fundamental component of the output voltage, line to line and line to neutral, and (b) the rms value of the actual output voltage line to line and line to neutral.
1- Using the simulator gnusim8085, write a program, which exchange of the contents of (B reg.) to the contents of the accumulator (A reg.) 2- Implement the following programs : Get a byte from monitor ROM : Store it in register D : AND 2880H in RAM : Stop : Load H and L from monitor ROM : Store H and L in RAM a- LDA 2850H MOV D, A STA 2880H HLT LHLD SHLD 2850H 2870H b- : Stop : Put 12H into register H, & 34H into register L : Put 56H into register D, & 78H into register E : Swap DE with HL : Stop : Store the MS sum byte : Stop HLT H, 1234H C- LXI D. 5678H LXI XCHG HLT MOV M,A HLT
8. An 8-bit ADC with a 10.0 V reference has an input of 3.637 V i. Determine the digital output. ii. What range of input voltages would produce this same output? iii. Suppose the output of the ADC is 101101012, calculate the input voltage.
1-An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the resolution of this ADC? 2-A thermocouple giving an output of 0.5 mV/oC. What will be the word length required when its output passes through an ADC if temperatures from 0oC to 1200C are to be measured with resolution of 1.50C?. Assume 12V as system voltage.
The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the voltage level applied to the ADC input is 1.67 V, what is the numerical value read? For numbers with commas, take 4 digits after commas.?
please give answer of this.. subject : microprosessor and microcontroller