Example 1: The equation of an angle modulated signal is: PFM (t) = 10 cos(10³t + 3 sin 10¹t) volts Determine: (a) The carrier & modulating frequencies. (b) The modulation index and peak frequency deviation. (c) The power dissipated in a 1000 resistor.

Example 1: The equation of an angle modulated signal is: PFM (t) = 10 cos(10³t + 3 sin 10¹t) volts Determine: (a) The carrier & modulating frequencies. (b) The modulation index and peak frequency deviation. (c) The power dissipated in a 1000 resistor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q2. For the scheme shown in Figure Q2, i. Draw the spectrum of the baseband signal (multiplexer…

A: The multiplication of any signal with Cosine signal in time domain leads to the shifting of the…

Q: A half-wavelength, lossless transmission line is 1.4 m long and terminated in 20 - j10 0. The…

A: For the lossless transmission line, the characteristics impedance is given as, In the question, the…

Q: so VC, Vm and modulation in DV and 75% and 50%

Q: Please show a two-terminal general modulation channel model. And for the random parameter channel,…

A: Modulation: Conversion of analog signal by sampling into 0 and 1 bits through carrier wave…

Q: List out any two problems that may occur in the reconstruction of the original signal and suggest…

A: Problems that may occur in the reconstruction of the original signal are Intersymbol interference…

Q: Q3) An FM modulator has a constant frequency deviation of 4KHz / volt. Determine the maximum…

Q: For question 1, The instructor asked what is an approach to modulate a PWM signal and what is an…

A: According to the question, we need to explain one approach for PWM modulation and detection…

Q: Is coupling a consequence of signal absorptions? What is the problem of this?

A: We need to explain coupling of signal absorptions.

Q: i) With neat sketch explain the cross sectional view and I-V characteristics of the device which is…

Q: Calculate the modulation indexes

Q: Use own words to clearly explain the interference phenomena of a) signal loss by frenquency out of…

A: Signal loss by frequency out of range is generally occurred in computers when input signal is loss…

Q: What are the key considerations in designing electrical circuits for high-frequency applications,…

A: RF circuits are built specially to work in high frequency applications and tackle all the issues…

Q: Consider a information signal: m(t) = 20 cos (2000JI t), carrier signal: c(t) = 50 cos (105 Jt). a)…

A: Utilizing modulation methods, the carrier signal so "carries" the voice or data information. Whether…

Q: A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with…

Q: (i) Define modulation index. (ii) Why is the amplitude of modulating signal kept less than the…

A: Amplitude modulation- When modulation is done by keeping the frequency and phase of carrier waves…

Q: Identify the given statement. Both the modulation index and the peak phase deviation in PM are…

Q: Write two factors justifying the need of modulating a signal. A carrier wave of peak voltage 12 V is…

A: Given:- The peak voltage of the carrier waveAC =12 V Modulation index μ=75% We have to find the…

Q: 2. What is the maximum efficiency value for an AM system that has a modulating signal a sinusoidal…

A: In this question , we have to determine the maximum efficiency of AM system for modulating signal of…

Q: 6. For an AM-DSB-SC system to become AM-DSB-TC, the modulating signal must include ... A. a CD…

A: According to the question, For an AM-DSB-SC system to become AM-DSB-TC, the modulating signal must…

Q: hoose the correct statement that describe the diagram below. Narrowband frequency modulator system…

Q: For the Amplitude Modulation AM waveform shown in the figure , determine the following: i.…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Q2. For the scheme shown in Figure Q2, Draw the spectrum of the baseband signal (multiplexer output)…

Q: Design a cascade of multivibrator circuits to convert a square wave from (10 kHz, 0.5duty cycle) to…

A: According to the question we have to design a cascade of multivibrator circuits to convert a square…

Q: What is difference between MOSFET, IGBT and BJT? Brief explanation about SCR.

A: To write: Difference between MOSFET, IGBT and BJT. Brief explanation about SCR.

Q: determine actual minimum BW in kHz (Blank 1) and the approximate BW in kHz. (Blank 2)

A: Frequency modulation- When modulation is done by taking frequency of information signal modulated…

Q: Activity 2: The amplifier circuit below has a single ac input and two ac outputs. Assuming…

A: For the above given question we need to calculate the value of Q point of the given transistor.

Q: (b) Derive the power calculation of AM signal.

A: Given: Brief description: Here in the above questions they want to know that derivation of the…

Q: find the system Noise factor and Noise Figure for Te = 30,50,75,150, and 300 K %3D measured at To of…

A: Given: The effective noise temperature measured at reference temperature 290K is: Te=30, 50, 75,…

Q: How to Sketch the AC equivalent of a given BJT circuit

A: Need to brief the procedure to get the AC equivalent of the BJT circuit.

Q: 1- Explain the principle of direct method generation of FM signal.

A: The explanation is as follows.

Q: A modulated signal with a bandwidth equal to 11.1 KHz. The LSB of the modulated signal is 9.6 KHz…

Q: 4a.i.) Discuss the PAM as applied in communication system. Outcome must be supported with a signal…

A: According t question we have to discuss about, (i) The PAM as applied in communication system.…

Q: Draw the band diagram of a modulation doped heterojunctions. And, use it to explain the advantages…

A: Heterojunctions are interfaces between two semiconductors having different gaps, they are one of the…

Q: Outline the circuit condition for using the supernode technique.

A: Suppose any of the branches in the network has only voltage source, then it is slightly difficult to…

Q: 3.38 The message signal m(t) into an FM modulator with peak-frequency deviation fa = 25 Hz/V is…

Q: What properties do it show that a modulated signal is an AM signal?

A: What properties do it show that a modulated signal is an AM signal?

Q: Given the figure below, discuss how the circuit recovers the original information from the input AM…

Q: 2. The output impedance of 600 ohms radio transmitter with signal strength reading on a meter of…

A: Pi-pad Attenuators: Pi-pad attenuators, also known as π-pad attenuators, are a type of balanced or…

Q: Design a cascade of multivibrator circuits to convert a square wave from (10 kHz, 0.5duty cycle) to…

A: According to the question we have to design a cascade of multivibrator circuits to convert a square…

Q: What can we eliminate negative parts of an AC signal, with and without using offset

A: Eliminate the negative part of the ac signal without using offset voltage Using a positive clamper…

Question

Example 1: The equation of an angle modulated signal is:
OFM (t) = 10 cos (108t + 3 sin 104t) volts
Determine:
(a) The carrier & modulating frequencies.
(b) The modulation index and peak frequency deviation.
(c) The power dissipated in a 1000 resistor.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: a) carrier and modulating frequencies

VIEW

Step 2: b) modulation index and peak frequency deviation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Define the following conceptsa. Positive modulation percentageb. Modulation efficiencyc. Signal strengthd. At least one technique for building an AM transmitter.
In ............. type of test signal ,the signal will have high magnitude at one time .
Given a low level AM modulator with a modulation index of m=0.8 a quiescent voltage gain A=100 an input carrier frequency fc=500Khz with an amplitude Vc=5mV and a 1000 Hz modulating signal. determine:a. Maximum and minimum voltage gainsb. Maximum and minimum amplitudes for Voutc. Sketch the AM output envelope.
Explain the difference between AC small signal amplifiers. from power amplifiers.
Multiple-choice questions: 1. When BJTs are used in digital circuits they usually operate in the: a. active region b. breakdown region c. saturation and cutoff regions d. linear region 2. Often a common-collector will be the last stage before the load; the main function(s) of this stage is to: a. provide voltage gain b. provide phase inversion (Inverting) c. provide a high-frequency path to improve the frequency response d. buffer the voltage amplifiers from the low-resistance load and provide impedance matching for maximum power transfer 3. A decrease in base current of a C.E. amplifier causes the voltage measured between the emitter and the collector to increase. a. True b. False
Does a PCM signal have a smaller bandwidth? Why or Why not?
A Phase Modulator has a phase deviation constant, Kp = 35°/V. The carrier signal is ec = 8 cos2n(800k)t, volts and the modulating signal is em = 5 sin2r(2000)t, volts. a. What is the equation of the PM signal? b. What is the maximum phase deviation? c. what is the amount of deviation in the carrier phase angle at t = 160µs?
Q2. For the scheme shown in Figure Q2, Draw the spectrum of the baseband signal (multiplexer output) for the multiplexer. Determine the bandwidth of the baseband signal (multiplexer output) for the multiplexer. Determine the minimum transmission bandwidth of the multiplexer. Explain, briefly, the modification needed for the multiplexer in the figure to achieve this bandwidth. i. ii. ii. 4 kHz cos 10,000xt Baseband signal 2 kHz cos 24,000nt cos 2000nt cos 32,000nt Figure Q2
Give the formula for modulation index and explain its terms.
In an AM signal with peak amplitude of 400 volts and a peak modulating voltage of 100 volts, what is the modulation factor? a.0.33 b.0.6 c.0.5 d.0.55
What is the objectives of generate discrete signal by using sampling frequency?
What are the advantages of MOSFET over JFET?