Ex. # 5) Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth are cut on the 20° full-depth system and have a module of m= 2.5 mm. Draw the free body diagram of gear 3 and shows all the forces acting upon it. Determine the forces acting upon gear 3. The direction of rotation of gear 3, as shown, is counterclockwise. GIVEN: Figure shown N₂ = 1750 rpm * = 200 P=2.5 kW m = 2.5 mm

Ex. # 5) Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth are cut on the 20° full-depth system and have a module of m= 2.5 mm. Draw the free body diagram of gear 3 and shows all the forces acting upon it. Determine the forces acting upon gear 3. The direction of rotation of gear 3, as shown, is counterclockwise. GIVEN: Figure shown N₂ = 1750 rpm * = 200 P=2.5 kW m = 2.5 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T=3N O O Input gear 11 teeth. Output gear 99 teeth 270 kgm² 57 kgm2 2.7 kgm2 Don't Know 27 kgm2 Flywheel 0.1 rad/s²
An epicyclic gear train is shown in the figure below. The number of teeth on the gears A, B and D are 20, 30 and 20, respectively. Gear C has 80 teeth on the inner surface and 100 teeth on the outer surface. If the carrier arm AB is fixed and the sun gear A rotates at 300 rpm in the clockwise direction, then the rpm of D in the clockwise direction is B D
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-wise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler.(a) Find the force F3b that gear 3 exerts against shaft b.(b) Find the torque T4c that gear 4 exerts on shaft c.
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclockwise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.
consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number of teeth on gear planeta (3) is Z3 = 20 and the number of gear anel (4) Z4 = 70 the speed of gear sol, w2 = 300 rpm and of anel w4 = 200 rpm find the speeds of gear sol and braço carregador b
In the figure below, a motor with power 150kw and speed of 2500 rpm is connected to shaft 1(by coupling) in a clockwise direction. Shaft 2 is connected to shaft 1 by gears 1 and 2. If 30% of the power is consumed by the gear3 and 9% by the pulley and 61% by the sprocket, draw torque diagrams for both shafts. If the pressure angle of the gears is 20 degrees to the x-axis, Calculate the reaction forces of the bearings and draw the bending moment diagrams for both shafts according to the information below: Lengths: AB=90mm/BC=DGH=50mm/CD=HI=60mm/DE=IJ=80mm Diameters: dG1=dG2=47mm/ dG3=20mm/ d(pulley)=35mm/d(sprocket)=40mm Gears Gear2 Tew) shaftz Bearing Shaft Gear1 SProcket
For the gear mechanism in the figure: P1 = 4 kW, η1 = 1000 rpm, z1 = 18, z2 = 36, z3 = 54, z4 = 108, z1 is the driving gear. Total efficiency values for each stage; Since η12 = η34 = 0.96; Find the output torque and speed of gear z4.
Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200 and 98) respectively. If the gear (S) rotate with speed (450 r.p.m.) in C.W. direction and the gear (A) rotate with speed (100 r.p.m.) in C.C.W. direction, Determine the speed of the gear (P) and the arm (H). [Note: Start motion from gear (S)]. A Good Luck
The figure shows a schematic representation of a gear system. The gears are meshed with one another and can therefore not slip. The ring gear R is fixed, i.e. wR = 0. Gear A has an inner hub with radius rA(inner) = 0.3 m which is fixed to the rest of the gear, having a radius of FAlouter) = 0.8 m, and moves together as a unit. Gear A is in mesh with gear B which has a diameter of de = 1.5 m. Gear B has a clockwise angular velocity of wg = 2.1 rad/s. Determine the angular speed of gear A. B TA(outer R
A bicycle's gear ratio is the number of times the freewheel turns for every one turn of the chainwheel (see figure). The back half of a bicycle is given. A line labeled "Freewheel" is pointing at the center of the rear wheel. A line labeled "Chainwheel" is pointing to the center piece connecting the two pedals. The table shows the numbers of teeth in the freewheel and the chainwheel for the first five gears of an 18-speed touring bicycle. The chainwheel completes one rotation for each gear. GearNumber Number ofTeeth inFreewheel Number ofTeeth inChainwheel 1 32 24 2 26 24 3 22 24 4 32 40 5 19 24 Find the angle through which the freewheel turns for each gear. Give your answers in both degrees and radians. (Round your answers to one decimal place.) gear 1 = rad= gear 2= ° rad= gear 3= ° rad= gear 4= ° rad= gear 5= ° rad=
consider a planetary train in the figure the number of teeth on gear sol (2) is Z2=30, the number of teeth on gear planeta (3) is Z3 = 20 and the number of gear anel (4) Z4 = 70 the speed of gear sol, w2 = 300 rpm and of anel w4 = 200 rpm find the speeds of gear sol and braço carregador b Anel (4) Planeta (3) ARRANT Sol (2)