Every morning, Jane walks from her house to her office and takes only a single route. In a whole week of walking, she decided to count the number of steps she made and recorded as follows: 392, 390, 401, 372, 381, and 417 paces. A person from City Engineer's Office was tasked to lay out a sewer piping system on the same route as Jane does and found out that the taped distance is 233m. What is her pace factor?

Every morning, Jane walks from her house to her office and takes only a single route. In a whole week of walking, she decided to count the number of steps she made and recorded as follows: 392, 390, 401, 372, 381, and 417 paces. A person from City Engineer's Office was tasked to lay out a sewer piping system on the same route as Jane does and found out that the taped distance is 233m. What is her pace factor?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use your calculator to obtain accurately to four decimal places the value of x if: a. x = log 798 b. 3x = 1n50 c. 105 d. 2e 8.9871
9:57 Done Edit Three masses are attached to a 100-meter long beam as shown below. The mass of the bea, is 210 kilograms and the masses my and mg are valued at 50 kilograms and 300 kilograms, respectively. Find the mass m2 that balances the system in SI units 30 m 40 m 30 m- m2 More
You need to answer in numerical form in two decimal places only unless otherwise specified. For problems having a whole number or zero as an answer, the decimal isn't necessary. For example, if your answer is 900, the decimal isn't necessary. No need to input the units, follow the units given by each problem. ROUNDING OFF VALUES MUST BE DONE ONLY IN THE FINAL ANSWER TO AVOID LARGE DISCREPANCIES. I'll rate!
A person by the name of Sutterland has developed a correlation that can be used to evaluate the viscosity of air as a function of temperature. It is given by
A wooden beam is loaded by a distributed load w =5 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 2500 mm, LBC = 2500 mm, W=190 mm, Bo = 30 mm, and H = 230 mm, ho=30 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. (а) (b) hol Во H В LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.
A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross- section of the beam is shown in Figure Q4(b). Assume that LAB = 2100 mm, LBC = 2900 mm, W=180 mm, Bo = 10 mm, and H=210 mm, ho=20 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. Steps: Fill the gaps in the "steps" to get some marks from the working-out process. Adaptive marking is still used. (a) (b) X ω LAB B mm4 LBC 7777 Show steps (Your score will not be affected.) Y Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam. N, y-direction: YA= a) Determine the 2nd moment of area of this cross-section with respect to the z-axis in Figure Q4(b)? I = N, y-direction: Yc= Section BC: Shear force equation V(x) =: Bending moment equation M(x) =: b) Calculate support reactions in A and C, remember the sign of the force. Reaction force at…
The x- and y-coordinates of a moving particle are given by the parametric equations below. Find the magnitude and direction of the acceleration for the specific value of t x=3t, y=4-t,t=3 Find the magnitude of the acceleration of the particle for the specific value of t. The magnitude is approximately (Type an integer or decimal rounded to two decimal places as needed.) C
The position of a particle is given by s = 0.30t³ -0.70t² - 2.50t + 4.99, where s is in feet and the time t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 8 seconds of motion. After you have the plots, answer the questions as a check on your work. Questions: 0 1 When t = 1.8 sec, V = When t = 6.5 sec, V = ●+ 2 i i +s, ft ft/sec, ft/sec, The positive time at which the particle changes direction is i a = a = i i sec. ft/sec² ft/sec²
Using the methods of this article, determine the surface area A and volume V of the body formed by revolving the rectangular area through 360° about the z-axis. Assume t = 12 mm, r = 28 mm, h = 10 mm. Answers: A = i IN V = IM mm² mm³
The following problems can be solved by writing commands in the command window. 8
The displacement of a particle that moves along the x-axis is given by x = (-4 + 3t^2)e^-0.25t, consider x to be in feet and t in seconds. Plot the displacement, velocity, and acceleration for the first 20 seconds of motion and determine, both graphically and by your established equation for acceleration, the time at which acceleration is 0. (If the students find it more comfortable, they may choose to graph using excel or any graphing software, solutions, however, must be done manually). Show COMPLETE STEP BY STEP SOLUTION and necessary FIGURES.
26. A prime number is a number that is evenly divisible only by 1 and itself. The prime numbers less than 100 are listed: 2 35711 13 17 19 23 29 31 37 41 43 47 53 59 61 677173 79 83 89 97. Choose one of these numbers at random. Find the probability that the number is greater than 50. O 1/25 O 1/5 O 2/25 2/5 ype here to search W Chp &