Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.Very very grateful!Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.Very very grateful! Estimate how the following process modifications affect to the efficiency of the gas turbine process, and connectright answers.Compressor intercoolingReheat combustorIncrease of compressor inlet air temperatureIncrease of the polytropic efficiency of the turbineReduces compressor powerIncreases the temperature after turbineIncreases compressor powerDecreases the temperature after turbine

Intercooling and increased turbine efficiency improve overall efficiency, while higher inlet…

Estimate how the following process modifications affect to the efficiency of the gas turbine process, and connect right answers. Compressor intercooling Reheat combustor Increase of compressor inlet air temperature Increase of the polytropic efficiency of the turbine Reduces compressor power Increases the temperature after turbine Increases compressor power Decreases the temperature after turbine

Estimate how the following process modifications affect to the efficiency of the gas turbine process, and connect right answers. Compressor intercooling Reheat combustor Increase of compressor inlet air temperature Increase of the polytropic efficiency of the turbine Reduces compressor power Increases the temperature after turbine Increases compressor power Decreases the temperature after turbine

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Similar questions

Question 2: (a) The pressure at which the steam should be reheated. (b) The thermal efficiency of the cycle. (c) Total heat input (Qin) (d) Total turbine work output (Wtur.out) (e) Draw the T-S diagram Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. • The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5% Boiler 650 C 17.5 MPa ww Reheater High-P turbine P₁ = Ps= Preheat Pump Low-P turbine Condenser e 15 KPa
Estimate how the following process modifications affect to the efficiency of the gas turbine process, and connect right answers. Increase of the polytropic efficiency of the turbine Choose... Choose... Increases compressor power Decreases the temperature after turbine Increases the temperature after turbine Reduces compressor power Choose... Reheat combustor Compressor intercooling Increase of compressor inlet air temperature + ◆
Q4// Answer A or B 201u, 4017 All What is the final part of the flue gas way of boiler furnace found to raise the temperature of water? Explain this?. Also, demonstrate briefly the water movement in power plant? B// What are the types of feedwater heaters in power plant, compare them? Explain the methods of cooling by these heaters and the ways of feeding.
Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at the inlet to the compressor is l'bar. The compressor is two stages and provided with perfect intercooler. The inlet temperature is 306 K and the maximum temperature is limited to'1073 K. the isentropic efficiency of compressor each stage is 80%. The isentropic efficiehcy of turbine is 85%. A regenerator is included in plant whose effectiveness is 0.7. Neglect the mass of fuel. Determine the thermal efficiency of the plant. Inter cooler 2' twww 3-0 supply L.P. Н.Р. Alternator Air in Biz & Bu Regenerator Exhaust
A steam turbine produces 2.5 MW of work. Steam enters the turbine at 4 MPa and 400oC. Steam out turbine at 1.4 MPa and 300 C.a. What type of turbine is this (back pressure, condensing,extraction)! Why?b. Determine the steam flow rate (kg/hour)! (51963)c. Determine TSR and ASR (units must be stated)! (13,13 and20.79 kg/kWh)d. Determine the efficiency of the steam turbine!
Question 4 A VRF cooling unit, having a cooling capacity of 25 kW, have the following COPS: COP100% = 369, COP75% = 5.72, COP50% = 6.65, COP25% = 8.16. Assume that the cooling unit has 13 hours of usage daily, having standby power of 200 W and energy tariffs of 41 cents per kWh. Using NEA's recommended AEC estimation, determine the annual energy cost up to 2 decimal points. Do not include "S" in your answer. Selected Answer: O 5,643.75 Correct Answer 5,584.12 0.01%
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
What is the advantage of having high steam quality compare to low steam quality?
It is desired to increase the compression ratio of spark ignition engine for 8 to 10. Assuming a ratio of constant pressure to constant volume specific heat to be 1.3, what will happen to the effeciency of the engine.?
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
How to Calculate the thermal efficiency of 400 MWth PBMR.PBMR, Helium using Brayton Cycle