ENG3043 Tutorial I A DC voltage source (Vs=10 V) is connected to a load (Z,= 100 Q) via a lossless transmission line (TML) as shown below. The voltage source has an internal impedance Z=50 Q and the TML has a characteristic impedance Z= 75 2. Calculate the phase velocity of the TML if its effective permittivity eeff is 2.56; ii. Calculate the source and load refection coefficients; i. iii. At t=0, the switch is closed. Draw the voltage waveform V(z,t) on the TML at t=2.5T where T is the time taken traveling from one end of the TML to the other and z refers to any position on the TML iv. Draw the voltage waveform at z=31/4 from the source for the time period between 0 and 3T; If the switch was open at t=1.5T, draw the voltage waveform at z=l/2 from the source for the time period between 0 and 3T Z, 1= 0 Z. V.

ENG3043 Tutorial I A DC voltage source (Vs=10 V) is connected to a load (Z,= 100 Q) via a lossless transmission line (TML) as shown below. The voltage source has an internal impedance Z=50 Q and the TML has a characteristic impedance Z= 75 2. Calculate the phase velocity of the TML if its effective permittivity eeff is 2.56; ii. Calculate the source and load refection coefficients; i. iii. At t=0, the switch is closed. Draw the voltage waveform V(z,t) on the TML at t=2.5T where T is the time taken traveling from one end of the TML to the other and z refers to any position on the TML iv. Draw the voltage waveform at z=31/4 from the source for the time period between 0 and 3T; If the switch was open at t=1.5T, draw the voltage waveform at z=l/2 from the source for the time period between 0 and 3T Z, 1= 0 Z. V.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.13P: A single-phase overhead transmission line consists of two solid aluminum conductors having a radius...

See similar textbooks

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination
The capacitance of a single phase two-wire transmission line depends on: Select one: a. All the above O b. the material of cables c. the radius of cables d. the distance between the cables O e. None of above
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight 1-The capacitance in uF/km without effect of ground is 2-The capacitance in pF/km with effect of ground is
A 300 km transmission line with a VR% of 95% and efficiency of 90% is operating with 230 kV voltage line. The load to be supplied is 300 MW with 0.8 power factor lagging. Determine the best values of resistance, inductance and capacitance that could match with the conductor configuration and code from Table A.3. Use the propagation constant value of 0.0456+ j0.4750 ohm and characteristic impedance of 406.4 cis (-5.48") ohms.
6-A lossless T.L. has Zo = 100 N and is loaded by an unknown impedance Its VSWR is 4 and the first voltage maximum is A/8 from the load . Find the load impedance .
Electrical Engineering A lossless transmission line has a capacitance per unit length of 90 uF/m (microFarad/meter) and an inductance per unit length of 1 nH/m. The load impedance ZI is purely resistive. Both the load impedance and the generator impedance are 50 ohms. Source voltage amplitude is unknown at this point. Find the characteristic impedance and the propagation velocity for this transmission line!
Quest- A single phase 50 Hz, system supplies an inductive load of 5000 kw at power factor 0.8 lag through a line 25 km. Resistance of the line is 0.0195 2/km and inductance = 0.36 mH/km, receiving end voltage is 10 kV. A capacitor is connected across the load to get the voltage regulation of 10%. Ratio of transmission line loss with and without shunt capacitor is
7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF
Expression for a voltage reflection co-efficient in terms of load impedance and characteristics impedance is: a) (ZL- Zo)/(ZL+ Zo) b) (Z+ Zo)/(ZL- Z) c) ZĻ. Zo/( Z+ Zo)( ZL-Zo) d) (ZL+ Zo)( ZL-Zo ZL. Zo