At t = 0, the switch in the circuit shown moves instantaneously from position a to position b. a) b) Calculate vo for t≥ 0+. What percentage of the initial energy stored in the inductor is eventually dissipated in the 4 resistor? 6.4 A t = 0 a b + Ve 62 m 10 Ω 0.32 Η 4ΩΣ

At t = 0, the switch in the circuit shown moves instantaneously from position a to position b. a) b) Calculate vo for t≥ 0+. What percentage of the initial energy stored in the inductor is eventually dissipated in the 4 resistor? 6.4 A t = 0 a b + Ve 62 m 10 Ω 0.32 Η 4ΩΣ

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Related questions

Q: Three charged particles are placed on the corners of an equilateral triangle of side 1.20 cm. The…

A: It is given that: d=1.20 cmQ1=+4μCQ2=-8μCQ3=-6μC

Q: Calculate the Fourier Transform of the signal x(t) = cos(2*pi*t) + cos(5*pi*t) and draw the signal…

A: Given: xt=cos2πt+cos5πt Required: (1)Fourier Transform of the signal x(t). (2)draw…

Q: Figure 2.1 shows the Asynchronous J-K flip flop and it truth table. Draw an output waveform, Q by…

Q: P 12.7-5 A three-phase Y-connected source simultaneously supplies power to two separate balanced…

Q: (9) A carrier frequency of 105 Hz modulated by a message signal m(t) produced an FM signal expressed…

A: Given here a FM signal and asked to find the modulation index.

Q: A three-phase motor draws 9 kVA at a lagging PF of 0.8 from a balanced system with line voltages of…

Q: 10 Q3) 1) Find the frequency f (Hz) 2) Find Zeg 3) Calculate all voltages and currents. 4) Draw a…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: What will be the value of R1 with the given RTL code XOR , where R1 is 1011 0110, R2 is 1100 0111

A: Given that in RTL code R1 is stored as R1 = 1011 0110 and R2 = 1100 0111 And the operation is XOR…

Q: find the steady-state response,

Q: Q5:- divide B/A:- • • • A=15m A, B= 800n a A=0.1m A, B= 13n a A=800m A, B= 1000n a • A=13m v , B=…

A: GIVEN: A=15mA, B=800nAA=0.1mA, B=13nAA=800mA, B=1000nAA=1mV, B=7000μV FIND: divide…

Q: What are rotor faults in alternators

A: The rotor of an alternator is directly connected with field winding of the alternator whenever there…

Q: Calculate the form factor and peak factor of a triangular wave in which the voltage rises uniformly…

A: Form factor: It is the ratio of the RMS value and average value. It gives information about the…

Q: Q2:- in electric circuit the current (5m A) when the voltage (1V) finds the value of current for the…

Q: Voltage != 5v Voltage 2: V Resistor 1 = 47-2 Resistor 2: 68 Resistor 3 = 39 Current 1 = ? Current 2…

A: Given data, V1=5 V, V2=7 VR1=47 Ω, R2=68 Ω, R3=39 Ω

Q: (b) For the circuit shown in Figure 2, the Vcc and BDc is 22 V and 65 respectively. Referring to the…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Half Wave diode rectifier circuit consists of Select one: O a. Two diode in Parallel with RL O b.…

Q: 40/60° V +1 2 Ω ww 16Ω -j4Ω Η j8 Ω 1:2 -j12 Ω FIND the value of Vı and Vá and Io. Topic:…

A: Given circuit with magnetically coupled coils of voltage ratio 1:2. To find V1, V2 and I0

Q: 2. a) Give a formulation of the Nyquist criterion for stability in both cases, when the open- loop…

Q: How do you get the value of Vab and Vac here? (YELLOW HIGHLIGHTED PART)

A: Given: A balanced 3-phase voltage source Van=200∠0°

Q: 2 -1 0¹ w(t) Figure Q1(b) 2

Q: Q3:- Determine the value of voltage (V1) and (V2) in figure (2-31) by using voltage divider rule. 45…

A: Given data : The given circuit is shown below,

Q: The following differential equation describes a water tank system 1 1 AR -h(t) ==q;(t) A where _h(t)…

Q: A continuous analog signal x(t) is sampled with a sampling rate of 600 Hz. The sampled signal is a…

Q: Vout Vx From Figure 3, analyse the circuit given to obtain the value of A if www HE 1292 39 12!! =…

Q: Describe with the help of

Q: -3s+1 s+a = Given a plant P (s) and a model for measureable output disturbance d with transfer…

A: Given,Ps=-3s+1s+aandQs=1s+bWhere,a=4.8b=9

Q: A plane wave propagating through a medium with er = 8, μr = -2 has E = 0.5 e-z/3 sin(108t - βz) ax…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: OR e) Explain the following protection schemes of alternators. i) Stator inter turn protection. ii)…

Q: b) Determine the number of poles on the right half plane, left half plane and on j-w axis for the…

Q: v(t) ► 10 0 -10 1 2 3 4 t (ms) FIND THE EFFECTIVE VALUE 31

Q: Determine the rms value of the ware form W+XV) 1 2 Į 2 3 4 5 t(s)

A: The given signal is periodic with period 4 sec. The formula and calculation is shown in the next…

Q: The intrinsic carrier concentration of silicon sample of 300 K is 1.5x10¹6/m³. If after doping, the…

A: Given: The intrinsic carrier concentration, ni2=1.5×1016m3 After doping the number of majority…

Q: the given RTL code XOR where R1 is 1011 0110, R2 is 11

A: Given as, R1 = 1011 0110, R2 = 1100 0111 RTL code XOR =?

Q: What will happen to the ammeter reading when switch S is closed? a) The reading will increase as…

Q: 1) Define a martingale sequence. Give the intuition of it and two examples.

A: In probability and statistics, a martingale is a series of random variables (also known as a…

Q: Vin = 10 V O a. 3.75 mA Ob. 2.5 mA 4k Ohm 4 k Ohm O c.- 1.25 mA O d. 5.7 MA The current it in the…

A: Here opamp is with positive and negative both feedback but negative feedback is dominating so it's…

Q: Determine the rms value of the unit sawtooth wave of period T.

A: The RMS value is Root Mean Square value. It is defined as " the amount of AC power that produces the…

Q: A transistor amplifier circuit is operated with an emitter current of 2 mA. The collector current is…

A: Given, In transistor amplifier circuit Emitter current, IE=2 mA Collector current, IC=1.98 mA

Q: An AM transmitter uses high-level modulation of the final RF power amplifier, which has a dc supply…

A: Given data, Supply voltage Vcc=36 V Current I = 2.8 A Efficiency η=77%

Q: 19 A balanced three-phase voltage source, Van = 200/0° V rms, positive phase sequence, is connected…

Q: 5- What are the Advantages of Fiber Optics?

A: Fiber optics ;- It is a technology which is used to transmit information as light pulses through the…

Q: 24 Lov 22 W Ejzn 1.97 21, tılım m 42

Q: H3. (Dynamical System ) Explain various types of oscillator in non linear system

A: Nonlinear oscillator : Whenever a force is exerted on any particle then there is movement in the…

Q: A resistance R, capacitance C, and inductance L are connected in series to a voltage source with…

A: Note: As per the policy we can solve only 3 sub parts of a question, please re-upload the remaining…

Q: An AM transmitter uses high-level modulation of the final RF power amplifier, which has a dc supply…

A: Amplitude modulation:- It is used for transmitting message with radio wave. It is easier to…

Q: For this circuit Is and V2 = R1 1Q Is R2 20 wwwwww V2 +Vs 12 V Select one: O a. Is = 1 A, V2= 2 V O…

A: Given circuit:

Q: A modulating signal given by m(t) = 5 sin[4 x 10³t 10 π cos(2π × 10³t)] V s fed to a phase modulator…

A: Phase modulated signal is given as xpt=Acosωct+kpxt Where, x(t) is the modulating…

Q: a. v = 10 sin(of + 30°) i = 5 sin(wt +70°) b. i = 15 sin(t + 60°) v = 10 sin(of - 20°) c. i = 2…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: I, 60/0° V +1 j15 Ω j100 Ω m j50 Ω j0 Ω ell 80 Ω j 10 Ω 40 Ω-j20 Ω ww j80 Ω +1 1, 20/90° V Find 11,…

A: Detailed solution is attached with the notes.please go through and follow up in case of queries.…

Q: Design and construct/draw a low-pass Butterworth filter with a roll-off of rate of -60 dB/decade and…

A: Given: A 3rd order low-pass Butterworth filter whose cutoff frequency is 10 kHz. Required: Design of…

Concept explainers

Sinusoids And Phasors

Sinusoids are defined as the mathematical waveforms that are used to describe the nature of periodic oscillations.

Circuit Theory

Electric circuits are a network that comprises of a closed-loop, which helps in providing a return path for the current through a switch. When the switch is activated, the load operates, and the current accepts a path to finish the circuit at a low potential level from the opposing high potential level. Electric circuits theory is a linear analysis that helps in establishing a linear relation of voltage and current for R (resistance), L (inductance), and C (capacitance).

Question

At t = 0, the switch in the circuit shown moves instantaneously from position a to
position b.
a)
b)
Calculate vo for t≥ 0+.
What percentage of the initial energy stored in the inductor is eventually
dissipated in the 4 resistor?
6.4 A
t = 0
a
b
+
Ve
62
m
10 Ω 0.32 Η 4ΩΣ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
The R-L Circuit: An inductor with an inductance of 2.50 H and a resistance of 7.00 n is connected to the terminals ofa battery with an emf of 6.00 V and an internal resistance of 1.00 n. What is the rate ofincrease of current at the instant when the current is 0.500 A? A) 0.8 A/s B) 0.6 A/s C) 0.4 A/s D) zero E) None of the above.
Determine the current through the 260mH inductor in the circuit shown in the figure and choose the solution from the options given. 0.7, ángulo de -2.9° 0.9, ángulo de -19.8° .52, ángulo de -23.1° 0.338, ángulo de 303⁰ 65 Ω 85mH 150 sin(2π 100t) mn 200 Ω 260mH 28 75 카 120 Ω 50uF
6. The waveform of the current in a 40mH inductor is shown in following Figure. Find the waveform of the inductor voltage. i(t) mA 4 10 -10 2 √141= -400 mu 400 md 400 mu -toomd 3 4 5 cetelus istszus 2stc3ms 31+64thl 4steśms 6 t (ms)
In the circuit shown in Figure, the switch S is closed at time t = 0. the voltage across the inductance at t = 0+ 3.02 10V A) 2V B 4V c) -6V D) 8V S 4F 492 HIMM WWW 49 ell
TRUE or FALSE a. A discontinuous change in the voltage requires an infinite current thus a capacitor resists an abrupt change in the voltage across it. b. The inductor takes power from the circuit when storing energy and delivers power to the circuit when returning previously stored energy.
Consider the circuit shown below, with an initially uncharged capacitor C and two identical resistors R. R O www V I C I₂ R C R At the instant the switch is closed, the current through the capacitor will be: zero At the instant the switch is closed, the current through the right-side resistor will be: V/R, directed Up After the switch has been closed for a very long time, it is opened. The current through the right-side resistor will be V/R, directed Down The switch is closed at t = 0. At t = ~ (long after) the current through the right-side resistor will be: V/2R, directed Down ✓ The switch is closed at t = 0. At t = ~ (long after) the current through the capacitor will be: V/2R, directed Up After the switch has been closed for a very long time, it is ope ed. The current through the be? V/R, directed Down pacitor will
1. Obtain the energy stored in each capacitor in the figure under dc conditions. 3 k2 1 k2 ww 20 F 10 V 10 F 6k2 ww
b) What is the current at t = 0.008 s? (In [A]) c) What is the voltage at t = 0.008 s? (in [V]) Hint: What relationships exist between voltage and current when the current in an inductor is interrupted?
In the circuit of the figure the switch is closed. Determine: The potential difference across the capacitor C=2μF for a very long time (t infinite) The energy stored in the capacitor to (t infinite)
Part C The L = 100 mH inductor in the following figure has an initial current of Io = 10 mA. If the voltage is, v(t) = le 10t+2e 5 V, what is the current, i(t), through the inductor? Express your answer as a function of time with units of mA.
switch is in position 2, circuit will discharge the inductor draw the circuit in discharge phase, the equations for v(t) and i(t) of the inductor for the discharge phase, and determine the time constant for the discharge phase