Q11 (a) If vi(t)=cos(2nx100000xt), determine the dvi(t)/dt. (b) If v2(t)=cos(2 Tx200000xt), determine the dv2(t)/dt. (c) Design an opamp circuit that can perform differentiation on vi(t) in (a), and give rise to a peak output value of 0.1 V. Verify that the circuit obtained can be applied to v2(t) in (b) and give rise to a peak output value of 0.2 V. [You need to specify the component values used in your opamp circuit.]

Q11 (a) If vi(t)=cos(2nx100000xt), determine the dvi(t)/dt. (b) If v2(t)=cos(2 Tx200000xt), determine the dv2(t)/dt. (c) Design an opamp circuit that can perform differentiation on vi(t) in (a), and give rise to a peak output value of 0.1 V. Verify that the circuit obtained can be applied to v2(t) in (b) and give rise to a peak output value of 0.2 V. [You need to specify the component values used in your opamp circuit.]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

clear and correct or dislike
Determine the meaning of these four specific number/letter codes used on capacitor labels 473K - 102J - 224M - 331J
Please asap
Find the 500K Rsh voltagea look Rang Rsh IG IAVO IG IAVE 0.03 7 70 525 500 600 350 3 7 70 700 262 To Imx Rm Rsh: I rang-Im 300 x31550 500-300 Ash 525 300x350 bo0 -300 Rsh = 350e %3D = 300X350 = 262n F00 - 300
Compute the cutoff frequency. C C 4.7 nF 'n O 2 kHz 1.4 kHz 2.82 kHz 3.12 kHz R₂ 12 k www 24 ko
Problem 7. A voice signal g(t) = 8 sin (2rt) volts is sent using a 4 bit binary PCM system. The quantizer has a step size of A = 1 Volt. Sketch the PCM wave for one complete cycle of the input assuming a sampling rate of 4 %3D samples/second, with samples taken at t = -3/8, -1/8, 1/8, 3/8, 5/8 seconds. The transfer characteristics of the quantizer is shown in fig.1 (see next page)
22. Write the logic expression for each of the circuits in Figure 15-60. Problems +V +V +V Rp A B C B D. D. 10 1001 E F F G D (a) (b) (c) FIGURE 15-60
Please show the process on finding for Vo and Ic. Answers were already provided. I need the solution. Thanks!
EXAMPLE 14-4 Determine the output of the DAC in Figure 14-19(a) if the waveforms repre senting a scquence of 4-bit binar numbers in Figure 14-19(b) are applied to the inputs. Input Do is the least significant bit (LSB). 40 k) D, o W RE 0 1 2 3 4 5 6 7 8 9 101I 12 13 14 15 20 ΚΩ +5 V D, o M 1.0 k Do 0- +5 V 10 k D2 0W +5 V o Vout D2 +5 V 5 k. D3 0W (a) (b) FIGURE 14-19
Review View Help 15-16-12- ALT Paragraph S A E Normal B No Spacing Label the function blocks of the voltage regulator D L Heading 1 YOUT H I= Heading 2 Styles
The faster response regulator should havedead band.O InfiniteO MoreO Low -maduam
RF twl-Draw the output wareform:-Ri 2. R2 >t R3 V3a Ideal >t Ri=RzE R3=Rpf=loK -015 - 2 Activate Windows