Electrical Engineering --question 1-- Calculate the theoretical voltages across the resistor and inductor for 10 kHz and 60 kHz using the 680Ω theoretical resistance, 3.3 mH inductance, and 5-V source. Demonstrate the step-by-step process. Answer must be in Polar form.

Q: Obtain the transfer function of a highpass filter with a passband gain of 10 and a cutoff frequency…

A:

Q: Given an Emitter-Stabilized Bias Common Emitter amplifier with the following data: Vcc = 12 V, lc =…

A:

Q: Q3. A link has a signal-to-noise ratio of 2000 and a bandwidth of 12000 KHz. What is the maximum…

A: Bandwidth is the difference between a upper and lower frequency of transmission signal like a Tv and…

Q: Consider the digital controller defined by G(z) Realized this digital controller parallel scheme.…

A:

Q: Find the following parameters 15.2 μA and Vc = iflg = 12 V for this transistor. a. lc b. ß C. VCE d.…

A: This problem can be done by knowing the relations between IC, Ib and Ie

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.0 KM www Bpc = 50 10 V 20…

A: We need to find out the current and voltage for given circuit.

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.0 k

A:

Q: what are the circuit that used to convert PWM to PPM? 3:43 ✔

A: PWM - Pulse width modulation PPM - Pulse position modulation   ---> The PPM Signal can be…

Q: Given: 120V, 60H₂, 30, 6 Pole, Y-connected IM R₁ = 0.08₁ X₁ = 0.3 S = 0,03₁ XM = 6.33 R2₂=0.07, X₂ =…

A:

Q: Refer to figure below, if the input A is more positive than input B, which diodes will be…

A:

Q: Describe the resulting waveforms when the capacitors (initially 20uF and then replaced with 100uF

A: Given, For 20uF capacitor, the output waveform is shown below,

Q: The values of Q1. Figure 1 shows a BJT amplifier whose voltage gain the components are shown in the…

A: BJT(Bipolar Junction Transistor):  Bipolar junction transistors (BJTs) use both electrons and…

Q: A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a…

A:

Q: Three resistors of 50 ohms, 100 ohms, and an unknown resistance R are connected in parallel and the…

A:

Q: 2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. R LOKO

A:

Q: 1.) R₁=56 201 A) RTOTAL = B) I TOTAL = C) V-TOTAL = R67 = E) V3 R₂=5 R3-20 R5=45 R6 = 3 R4=252 M R7…

A:

Q: (1) Please don't write on a paper. I can't understand handwritten well. 1. DETERMINE THE MAGNETIC…

A: Magnetic field strength: It is a force that is applied to the moving electric charge. This is…

Q: 2 The total charge entering a terminal is given by q=10(1-e') mC. The current at t = 1.609 sec is…

A: Given, Total charge entering a terminal q=101-e-t mC Time, t=1.609 s

Q: An unknown load draws 15A when connected to a 240V AC source, when connected to the same circuit,…

A: Given, An unknown load draws, Current, I=15 A AC source, V=240 volt Power consumed, P=3 kW

Q: Given an Emitter-Stabilized VCC = 12 V, lc = 2 mA, VC = 7.6 V, VE = 2.4 V and 3 = 80 Bias Common…

A:

Q: Determine IE, VBE, VCE, and VCB in the circuit. Assume BDC = 150.

A:

Q: Given the amplifier circuit below, solve for the following, Zin, Zo, Avs, AIS 18V +V Q 1k C1 119 200…

A: Given the circuit, as shown below: We need to find Zin , Zo , Avs , AIs

Q: A current of 2 -j 4 amperes is flowing through a circuit. The magnitude of current is

A: Given, Current flowing through the circuit, i=2+j4

Q: .8 μm. Calculate: a. Power supply, when the power from the fiber output is 5 μW. b. SNR report that…

A: A PN silicon diode is nothing but a PN junction diode it allows the flow of current in only one…

Q: The impedances Z₁ = 6 + j8, z₂ = 8 −jk, and z3 = 10 + j0ohms measured at 50Hz from three branches of…

A: this is a parallel circuit so first calculate the total admittance Y=1/(6+j8)+1/(8-j6)+1/(10+j0) =…

Q: Determine the stability of the control system by applying the Routh Stability Criterion to the given…

A: In this question,  We need to determine the stability of the control system using the routh…

Q: 04: One branch A of a parallel circuit consists of a 50-µF capacitor. The other branch B consists of…

A: Given data-CA=50μF , RB=30Ω, LB=0.2 H, Rc=140ΩVs=230 V f=50 HzThe circuit diagram will be- To solve…

Q: For the circuit shown in the figure below, if the current flowing through R: equals 0.1mA UnCos…

A:

Q: Design the MEMORY and I/O Subsystem based on the given specification with complete solutions. A…

A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: _______ action eliminates the offset described above by moving the controller output at a rate…

A: This is the  question related to the understanding of controller and it's various techniques.There…

Q: R₁=5₂ 201 A) RTOTAL = B) I TOTAL = VTOTAL = R67 = E) V₂ R3-22 R₂=55 R5=45 R6 = 3 R4=25 M R7 = 3

A:

Q: A combination of three resistors R1, R2, and R3 in series is connected across a voltage source VT.…

A:

Q: Is the synchronous motor works on the principle of magnetic attraction? TRUE or FALSE

A: Yes, synchronous motor works on the principle of magnetic attraction or magnetic locking.

Q: The bus admittance matrix for the power system shown in Figure 1 is given by 3-j9 −2+j6 -1+j3 0 Ybus…

A: Gauss-Seidel (G-S) method is one of the simplest iterate method. It is a modification of…

Q: In a balanced three-phase Y-Y system, the source is an abc sequence of voltages and Van = 148∠8°…

A:

Q: Explain the difference between DOL starting and Autotransformer starting also explain the working…

A:

Q: Q2 A series RLC bandrejec calculate the values of L an

A:

Q: If Vab = 135 Vrms in a balanced Y-connected three-phase generator, find the magnitude of the phase-c…

A:

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 K 10 V +4/+ H1₁ www 20 KQ…

A:

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Rc 1.0 KO RB Vcc 10 V Bpc = 50…

A:

Q: Q5) Impulse response of a causal LTI systems is given as in the following. Find impulse responce of…

A:

Q: Simplify the complement of Boolean Expression using DeMorgan’s Law Z= (BC’ + A’D) . (AB’ + CD’)

A:

Q: Three zones of a single-phase circuit are identified in the figure with a generator voltage…

A: For the evaluation of electrical machines, one-of-a-kind values are required, consequently, per unit…

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Rc 1.0 KQ Vcc RB www 10 V 20 kN…

A:

Q: Determine the voltage gain of an amplifier that has an input signal of 4mA at 15mV and a…

A: In this question we need to choose a correct option

Q: A capacitor of capacitance 120 µF is connected across a 220 V, 60 Hz A.C. mains. Calculate the value…

A: 22)

Q: A control system is shown in figure below. Determine the steady state erver for a unit, step input…

A:

Q: B) For a system with the transfer function What is the DC gain of the system? 10s+200 G(s)=2+10s…

A: Given, The transfer function, Gs=10s+200s2+10s+100

Q: Find the Vx in the network below:   Round off the final answer to four decimal places, polar form,…

A: The voltage across the resistor can be calculated by using the mesh analysis in the circuit

Q: The voltage of a source is e = 220 cos (wt - 1200) while its three loads take currents given by…

A: A closed path, where electric current can flow defined as an electric circuit. It is various…

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.