A prestressed hollow box cross section is shown in the figure. The area of prestressed reinforcement in the tension zone is 1148 mm2. Usegrade 270 for seven wire-strand tendons.fpy = specified yield strength of tendonsfpu = specified tensile strength o pre stressing tendonsfse = effective prestress after lossesfse = 1022 MPaAps = 1148 mm2fpy = 0.95fpufc' = 34.5 MPafpu = 1860 MPa600 mm125 mm350 mm125 mm125 mm700 mm500 mm125 mm50 mma. Compute the Yp factor.b. Compute the stress in prestressed reinforcement at nominal strength.c. Compute for the design moment capacity.d. Compute the effective pre stressing force after losses of stresse. Compute the depth of the compression block.f. Compute the pre stressing steel ratio.

solution data given fc' =34.5 MPa Ec= 4700×fc'Ec =4700×34.5 =27606.25 N/mm2→ for graded 270 , Es…

Answered: e strength o pre stressing tendons ess…

Engineering

Civil Engineering

e strength o pre stressing tendons ess after losses

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a". %3D
1. Differentiate the permanent and the variable action with suitable examples 2. Analyze the stress-strain relationship of steel. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
1. The prestressed beam is pre tensioned by a bonded prestress tendon having an area Aps = 650 mm2. fpu = 1728 MPa fpe = 988 MPa %3D fpy = 1486 MPa fc' = 27.6 MPa 300 mm |120 400 mm 600 mm 120 100 a. Find the value of the stress in prestressing reinforcement at nominal length. b. What is the design moment strength of the beam c. Is the beam over or under reinforced.
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A pretensioned member with a dimension of 250mm x 360mm is subject to an eccentric tendon that is located 105mm from the soffit. Area of the prestressing steel to be 502 sq. mm and the modulus of elasticity is 200 GPa. The Modulus of elasticity of concrete is 36.8 GPa. Creep coefficient = 1.6 and the shrinkage strain = 3 x10^6. Assume a 5% steel relaxation. Find the total prestressed loss in percentage.
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.4 in., d = 13.2 in., a = 3.4 in., and t= 0.7 in. For a vertical shear force of V= 36 kips, determine the shear flow through the welded surface at B. %3D B b. Answer: kip/in.