e la a a g. agua h A 0 2,1 m 2,8 m

Q: Compute the maximum moment and maximum shear developed in the beam below due to the wheel loads of a…

A: First draw the free body diagram seperately and then proceed the problem

Q: Q.2. Determine the moment of inertia of the composite area about the x and y axis. 150 mm -150 mm--…

A:

Q: The joint is subjected to the force system shown in the figure below (Figure 1) where P₁ = 270 lb…

A: given data  P1 = 270 lb P2 = 480 lb find the combined normal stress at point B.

Q: Two plates 20 mm thickness are fastened by a number of 25 mm diameter rivets, a tensile load of 500…

A: given data thickness of plate = 20 mm diameter of rivets = 25 mm tensile load = 500 kN shear stress…

Q: A/43 Determine the moment of inertia of the shaded area about the x-axis in two different ways. 40 ㄸ…

A:

Q: QUESTION 17 The inequality in the Clausius inequality holds for A. internally OB.irreversible…

A: Concept: Clausius Inequality: The cyclic integral of (dQ/T)<= 0 For dQ/T <0 , Process is…

Q: Example 4-1: A perfect gas at pressure of 750 kPa and 600 K is expanded to 2 bar pressure. Determine…

A: Given: P1 = 750 kPa T1 = 600K V1 = 0.2 m3 V2 = 0.5 m3 P2 = 200 kPa

Q: please explain part b a, Calculate the F and FB reaction forces that act on the overhanging simple…

A:

Q: A spiral transition curve is used on railroads to connect a straight portion of the track with a…

A:

Q: Example 3 A house requires 2 x 105 kJ/h for heating in winter. Heat pump is used to absorb heat from…

A:

Q: Question 5: For a rolled steel beam of an unsymmetrical I- section as shown, shown in Fig. 5. If the…

A: First calculate the position of neutral axis from bottom surface.

Q: 30° /braking system has its braking lever inclined at an angle of 30° to the horizontal plane, as…

A: GIVEN DATA- DIAMETER OF BRAKE DRUM D=540mm FORCE F=600N COEFFICIENCT OF FRICTION =0.4 WE HAVE TO…

Q: Q1. For a compressive helical spring which was made of alloy steel with (200MPa) yield stress,…

A:

Q: • A stone is thrown horizontally at +17 m/s from the top of a cliff 40 m high. How long does the…

A:

Q: 10. At the instant shown the boomerang has an angular velocity w = 4 rad/s and its mass center G has…

A: given data  Vg= 6 in/se w= 4 rad /se find the velocity of point B.

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? O…

A: Blanking and punching are sheet metal cutting operations.  Blanking: In the blanking operation, the…

Q: No. a) b) c) e) T, °C 125 75 P, kPa 200 1000 500 850 I, kJ/kg 1600 2950 0.6 0.0 Phase description

A: Given: P= 200 kPax= 0.6 Solution: Given that, x= 0.6. Hence, it is in wet region. For wet region,…

Q: A horizontal cylinder of internal diameter 100 mm is filled with water and rotated about its axis…

A:

Q: 4. Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4MPa,…

A: given data  P1= 4Mpa T1= 500°C V1= 80m/s P2= 30kPa x=0.92 V2= 50m/s mass flow rate = 12 kg/s find…

Q: two plates are fastened by a number of rivets and a tensile load of 300 KN is applied, find the…

A:

Q: Determine the value of coefficient of friction if friction force is 300 N and Normal force is 1000 N

A:

Q: Water flows through a pipe of constant radius = 10 cm with a speed of 4 m/s and a pressure of 250…

A: given data constant radius = 10 cm  speed at A = 4 m/s pressure at A = 250 kpa find the velocity and…

Q: Q4/ One mole of an ideal gas, initially at 20°C and 1 bar, undergoes the following mechanically…

A:

Q: Without writing shear and moment equations, draw the shear and moment diagr ams for the beams…

A:

Q: Q2: Air flows out of a nozzle straight up 30 m. What is nozzle velocity exit?

A: Given data : Acceleration due to gravity=g Height from nozzle=h   To find : Velocity exit

Q: Q5/ An existing process consists of two steps: (a) One mole of air at T1=900k and p1= 3 bar is…

A:

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? O…

A: For sheet metal cutting process called blanking,  the cut piece is the desired part.

Q: 7.41 An uncold-worked brass specimen of average grain size 0.008 mm has a yield strength of 160 MPa…

A:

Q: Q1/ Water flow through an orifice meter at an empirical equation Re = 0.35Re0 and a rate of 300*106…

A: INTRODUCTION: The pressure differential between the orifice meter will be calculated in this issue.…

Q: Find the centroid of the shaded plane with respect to reference axis in the figure shown below. 2 m…

A: Answer: The centroid of the shaded area: (X, Y) = (3.1110 m, 1.9496 m)

Q: Q1. For a compressive helical spring which was made of alloy steel with (200MPa) yield stress,…

A:

Q: Q2: Air flows out of a nozzle straight up 30 m. What is nozzle velocity exit?

A: given data the straight up height = 30 m find the nozzle exit velocity.

Q: A heat exchanger in which air passes over tubes through which cold Refrigerant-22 flows. Air enters…

A: Given DataP1=1.2 barT1=37°CT2=25°CP2=100kPaV1˙=50 m3/min As in given statement there is no mass flow…

Q: If the coefficients of static and kinetic friction between the 30-kg block A and the 83-kg cart B…

A: given data  mass of A = 30 kg mass of B = 83 kg coefficient of friction = 0.56 find the acceleration…

Q: Is it possible to ask for a drawing of the involute profile of at least 2 complete teeth of the…

A: Addendum is the height of the pinion tooth from the circumference of the pitch circle and dedendum…

Q: The motion of a particle is defined by the relation x = t²(t-3) ³ where x and t are expressed in…

A:

Q: A force F acts on the box as shown. The box is about to slide down. Determine the value of F if θ =…

A: Given   Coefficient of friction = 0.33                        Mass, m = 42 kg Find     Force, F

Q: A car starting from rest moves along a straight track with an acceleration as show Determine the…

A: Given  V=50m/s

Q: a. State carefully the differences between wire frame and solid modeling? b. Verify the

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: TURRET LATHE Types of turret lathes Principal parts of a ram -type turret lathe Different universal…

A:

Q: and point out the range

A: The plot of polytropic process on P-V and T-S diagram for endothermic, volume decrease, heating and…

Q: find the air flow through circular duct if the diameter(350mm) and velocity(6m/s)

A: Given data : Diameter=d=350 mm Velocity=V=6 m/s   Required : Air flow

Q: P Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: given data force P = 2kips cross section = 1.6 in × 1.6 in find the combined stress at point A.

Q: Q3/Evaluate four of the following integral. dx dx c. fd. f d e. f(3x + 2)5 dx 1 sec²x

A:

Q: Consider a bouncing ball. At time t = 0, the ball is dropped from a height_y(0) = ho, where ho is…

A:

Q: Refrigerant-134a at 1 MPa and 908C is to be cooled to 1 MPa and 308C in a condenser by air. The air…

A: Given data as per the question considering the values from the fig Pressure at inlet =1 Mpa The…

Q: Q1: For the beam ABCD subjected to the loading shown in figure below (B interral hirage) (1) draw…

A:

Q: It is observed that the skier leaves the ramp A at an angle 0= 25 with the horizontal. If he strikes…

A: Given: VA=19.4231 m/sVB=40.4097 m/stAB=4.5446 m/s To find: d. Radius of curvature at A, RAe. Radius…

Q: Air at a pressure of 1 atm. abs. and 50°C flows parallel to the top surface of a rectangular plate,…

A:

Q: Q5: The space between a square smooth flat plate (50 x 50) cm², and a smooth inclined plane (1:100)…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.