Answered: Ductility characteristics are…

Ductility characteristics are introduced due to which type of defect .a Point defects .b Line imperfections .C Surface imperfections .d Volume imperfections

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter44: Semiconductors

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Related questions

Q: In hot working of metals, the distorted grains are completely removed and fresh new grains are…

A: In hot working of metals, the distorted grains are completely removed and fresh new grains are…

Q: The property of breaking without much permanent distortion is Ductility. Select one: O True O False

A: Since you have Multiple Independent questions we will solve the first question for you To get the…

Q: State the advantages and disadvantages of natural diamond bits.

A: Given:- Natural diamond bits To find: Advantages and disadvantages of natural diamond bits

Q: What types of materials microstructure were shown using the tools in the lab? Ceramics, metals or…

A: In this problem, it is asking about the type of material micro-structure that is shown using the…

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: The fine grains have lower toughness than coarse grains. Select one: True False

A: the given statement is false.

Q: Grain size does not have a major influence on mechanical properties. True False Identify the…

A: Answer: 1.IT IS FALSE Because grains has measurable effect on most mechanical properties. Such as…

Q: Ideal crystals are always have imperfections in a crystal structur

A: No, ideal crystal does not have imperfections.

Q: Which is/are not reasons why brittle ceramics stress-strain behavior are not determined by the…

A: correct options are- a) It is difficult to grip brittle materials without fracturing them.

Q: 3 l Two tensile samples were cut from a titanium ingot that was cooled very slowly, and under…

A: Tensile material such as titanium with single crystal made from a ingot that is cooled very slowly…

Q: Volume imperfections are zero dimensional defects

A: Statement is false

Q: Angle probes 15)A flat surface specimen is examined using a 50o angle probe,and a defect echo is…

Q: Which of the following is an example for surface treatment process. a. Annealing b. Tempering c.…

A: Annealing is the heat treatment process that is generally used to increase the ductility property of…

Q: Hot hardness means that the material will lose its hardness at high temperature. True or false and…

A: The hardness of a material is associated with the strength of the material. This is associated with…

Q: Macroscopic examination is distinguished from microscopic examination by: The low magnification…

A: Macroscopic examination is distinguished from microscopic examination by: The low magnification…

Q: Check the correct statements. a) The huge differences between the values of theoretical strength…

A: Solution: The correct statements and the necessary explanation is given below:

Q: A non-destructive test is any examination of an object in any manner which will not impair the…

A: True , A non-destructive test is any examination of an object in any manner which will not impair…

Q: Mechanical Engineering Statics of Rigid Bodie

Q: List and describe all the types/kinds of point defects.

Q: Which of these related to zero-dimensional defects? Frenkel Inclusion Twin boundary Edge dislocation

A: Zero dimensional defects is the point defect which arise due to impurity or vacant atom.

Q: Two previously undeformed specimens of the same metal are to be plastically deformed by reducing…

A: The hardest specimen will be the one that has experienced the greatest degree of cold work. So,…

Q: Real crystals are always have imperfections in a crystal structure. Select one: True False

A: True.

Q: What are the means of elastic and plastic deformations?

A: Given: Deformation To write Means of elastic and plastic deformation

Q: On the drawing attached, what is the coaxility tolerance that is implied between the two diameters…

A: Given: ∅O=30/30.2∅I=12/12.3To find:Coaxility tolerance

Q: Briefly Explain effects of defects on the properties of materials.with diagrams?

A: Given Data⇒ Defects Properties of materials

Q: Why do we need to calibrate temperature measuring devices?

A: Temperature measuring devices can range from thermometers to optical sensors. Generally, these…

Q: What happens if you add a small imperfection to a system that has a saddle-node bifurcation?

A: A bifurcation is a shift in the qualitative nature of a solution as a control parameter is changed.…

Q: Which of the following defects is called as 1 Dimensional defect O a. Volume imperfections O b. Line…

A: Point defects are zero dimensional defect Line imperfections are One Dimensional defect Surface…

Q: On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance…

A: The tolerance for how near one cylinder's axis is to another is known as coaxiality. A shaft with…

Q: Which of the following is/are TRUE? OEdge and screw dislocations lower the required shear stress for…

A: The reduction in area in low carbon steel is expressed as, Thus, a reduction in area is…

Q: is the property of a metal which resist the external forces to scratch. a. strength b. Creep C.…

A: hardness is the property of a metal that resists plastic deformation or indentation, penetration it…

Q: Real crystals are always have imperfections in a crystal structure.

Q: Listed below are four categories (i.e., types) of defects. Give one example for each type of defect…

A: point defect Point defects are where an atom is missing or is in an irregular place in the ionic…

Q: Given a ceramic material which contains large defects with similar sizes (these defects are small…

Q: Define the slip angle-

A: In the case of a four-wheeled vehicle, it is essential that no wheel is lifted off the ground while…

Q: Which would be the most likely to measure for an inflated baloon? A. Shear modulus b bulk modulus…

A: Which would be most likely to measure for an inflated balloon....... First and foremost what is…

Q: Which of the following is “Surface treatment” process ___________? a. Annealing b. Extrusion c.…

A: Which of the following is surface treatment process Surface treatment is a process in which some…

Q: Identify the steps preparation of metallographic specimen. Grinding Washing Sectioning Polishing…

A: Metallography:- It is the study of the physical structure and components of metals by using…

Q: Ideal crystals are always have imperfections in a crystal structure.

Q: Q2)) Fill the following blanks: A) Crystal structure can be found as ------ and B) Metals lattice…

A: A) Crystal structure can be found as ---------- and........... B) Metals lattice structures are…

Q: ACE Metals produces and machines titanium castings for aircraft components. A critical dimension is…

A: Given: The basic diameter of the component is D=0.850 in. The tolerance in the component is T=0.050…

Q: d) Name the imperfection of crystals an extra half plane of atoms “inserted” into the…

Concept explainers

Crystalline Imperfections

The crystalline imperfections are described as the geometrical defects in the crystal due to incorrect arrangement of atoms, impurity, vacancy, and many more. It is not possible to achieve a perfect or ideal crystal, practically.

Question

Ductility characteristics are introduced due to
which type of defect
.a
Point defects
.b
Line imperfections
.C
Surface imperfections
.d
Volume imperfections

Which of the following crystal structures are
harder and malleable
.a
FCC
.b
SC
.C
НСР
.d
ВС

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Help me please
A half a plane of atoms are inserted into the crystal lattice is known as_ O Screw Dislocation O Edge Dislocation O Surface Imperfections O Grain Boundary Imperfections
The orderly arrangement of atoms in a structure is known as crystalline structure. Select one: True False
3 Copper Unit Cell Uniqueness Here's a weird way to describe the structure of copper: Cu falls into the tetragonal crystal system with a = 0.256 nm, c = 0.362 nm = a√√2, and atoms located at 000 and. Its density is 8.94 g/cc at room temperature. (a) Draw a few adjacent units cells of the structure as described in this "weird" way. You should be able to see that there is a much more convenient way to describe the structure. What is it? (The point I wish to make is that there are many different unit cells that can be used to describe any given crystal, so we usually choose the one that is easiest to visualize.) (b) Calculate the radius of a copper atom using the above information. (c) Calculate the lattice parameter of the "better" unit cell of Cu.
Determine the indices for the following crystallographic direction. Must show complete solution following the steps below, and use proper notation. Steps in defining the 3 directional indices 1. Vector repositioning (if necessary) to pass through origin. (needed in this case) 2. Read off projections in terms of unit cell dimensions a, b, and c 3. Adjust to smallest integer values 4. Enclose in square brackets, no commas → [u v w]
Calcium has the Face-Centered Cubic (FCC) crystal structure shown in the figure below. The atomic radius of calcium is r = 0.197 nm at room temperature (20°C). Calculate the edge length "a" of the unit cell Select one:. O a.0.333 06.0.488 Dco.557 Oa0612 The ndlces fer the direction shown in the figure are, 9:11 PM A D O 4) ENG 15-Apr-2021
For the images shown below, which Miller indices for crystallographic planes are included? lu C. Z Select one or more: a. (111) b. (230) (211) d. (110) e. (100) b y X a/2 Z b Z 2b/3
Ly Moving to another question will save this response. Question 36 There is L three-dimensional crystal structures? Moving to another question will save this response. OL LO 0 W
The spacing between two adjacent (123) planes in a simple cubic crystal with the lattice parameter a=0.4 nm is _______ (nm). Draw [322] in a body centered cubic crystal. Draw (202) in a face centered cubic crystal. The planar density of (003) should be higher than that of (002) in a body centered cubic crystal. Ture___ or False____. You need to justify why to the answer.
D Name the Crystallographic Direction and Show the Steps
Density of crystal materials can be determined based on their microstructures. True or false?
The unit of the atomic packing factor APF is: Select one: a. m3 b. Unit less С. ст3 d. None of these