Draw the shear and moment of the following structures 1. GO KN/m 4m 30KN/m 30 EN 2m узьком X

Q: 32 5 KN 10 KN 8m A THIT A HINGE 15m с 12 KN 13m C 30 KN 5m

A: A simple frame is as shown below: To find: To draw SFD and BMD

Q: draw the shear force digram and bending moment digram and contraflexer point

A: Given:- Overhanging beam To find:- a) SFD b)BMD c)Point of Contra flexure

Q: 50KN 50KN A B 5m 5m 5m 5m

A:

Q: Solve the shear force, 6ft to the right from A.

A: Solve the shear force, 6ft to the right from A.

Q: solve for the remaining reactions and also put the directions

A:

Q: Influence Line: Moving load group Determine the largest (absolute value) of the shear just left of C…

A: Consider the beam diagram;

Q: 3 kips/ft |4 kips B В D A – 4.5 ft– -3 ft→ | 1.5 ft

A:

Q: Q1 Draw the Shear force and Bending moment diagram 5kN/m R 2m 2m

A:

Q: Draw the shear and bending moment diagram.

A:

Q: Draw the shear and moment curves label the maximum values of shear and moment. Blank 1 MN kips B↓…

A:

Q: 1-49. The railcar lamp is supported by the -in.-diameter pin at A. If the lamp weighs 4 lb, and the…

A:

Q: 3/59 The vertical mast supports the 4-KN force and is constrained by the two fixed cables BC and BD…

A: Given data

Q: What is the Maximum moment in kN-m. Given: w - 15, a 1, b-5, and c-3. w kN/m A D. -am b m cm

A:

Q: 4e. Draw the qualitative (i.e. no values) Influence Line for the vertical reaction at C. A B A B 4f.…

A: Given continuous beam with support and hinges,It is asked to draw the ILD for following,1.…

Q: draw the shear, moment and normal forces diagram 60kNm 10kN 4m B. 2m 2m 4m

A: We will take moment at hinges as zero.

Q: 17

A:

Q: 5. Find the force in the member QS of the frame shown in figure. a 566N b. 400N c. 773N d. 1090N

A: Equilibrium equations are used to determine various force values in a structure. The equilibrium…

Q: 40KN F 4m b G 100KN D E 6m 777T 6m to 8m

A: The portal method is generally suitable for analysis used for analyzing building frames objected to…

Q: F4-7. Determine the resultant moment produced by the forces about point O. 500N 3000 N 45 25 m 00N…

A:

Q: 1. Determine the values of the shear V and the moment M at the following locations: immediately to…

A:

Q: Draw completely the shear and moment diagram 2 k/ft A C E18 ft- 15 ft- 18 ft - Figure 3

A:

Q: 18

A:

Q: d by the load a ler support is p

A: We knowDeflection due to udl at end is :δudl=wl48EiDeflection due to point loadhere reaction of…

Q: Draw completely and clearly the shear and moment diagram 2 k/ft A C 18 ft 15 ft 18 ft-

A:

Q: Bending moment is known in the beam ABC in section B: MB = -10 kNm The magnitude of the charge w.…

A: The FBD of the section is shown below: Here, The equivalent point force=Area of loading F=12w3+1=2w…

Q: Draw the shear force digram and bending moment digram

A: Given data in question UDL 20kN/mPoint load 40 kNSpan 6 mTo find out SFDBMD

Q: A 120 kN 15 kN/m HIIIIc Į EIIII PAWANNACRO CONGO G B F D Hinge Hinge -8 m-5 m+5 m-5 m+5 m - 8 m - 10…

A: Given:- To find:- Shear force and bending moment diagram

Q: 10 kip/ft 50 kip ft A 5 ft 5 ft The simply-supported beam above is subjected to a uniformly…

A: Apply equilibrium condition : ∑MB=0RAY×10-10×5×(52+5)+50=0RAY=32.5 kip

Q: Draw the shear and moment diag of the beam loaded as showr in figbelow 30KN sol. 50 KN Im 지

A:

Q: Determine the tension in the cables AD in KN that appear in the Figure to keep the load of 100 kg in…

A:

Q: Problem 2: Replace the three forces which act on the bent bar by a force-couple system at the…

A: In this problem, we are given three forces acting on a bent bar. We must replace these forces with a…

Q: Calculate the reactions at each support. Draw the shear, moment, elastic curve and axial force…

A:

Q: Determine the force in G a E 400 N 3 m B D 4 m- 1200 N 4 m 8. member GE of the truss. a. 568 N C.…

A:

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: Given:- A=8B=6C=8Y=29 To find:- Reactions at the supports Shear force at (A+4) ft left of C Shear…

Q: Determine the componets of the reactions for the beam. Please show all work

A:

Q: Calculate moment reaction at support A

A: Given: Cantilever beam with following loading condition   To calculate: Moment reaction at A, Ma

Q: An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative…

A:

Q: Find the vertical reaction at roller support. 20 KN 10 KN 4 000 20 KN 4 0000 AO

A: To find out the reaction at roller support.

Q: 2.7500 0000- 0000- 0000- 0000- 0000 70KN 80KN 90KN

A: let,RA=vertical reaction at A in upward directionRG=vertical reaction at G in upward directionusing…

Q: A 2 kN/m 6m 6 kN 4m 2m

A:

Q: please solve and draw the shear and moment diagrams 40 kN 60 kN-m A B C ksmk-5 m-k-5 m–+tsml- 10 m

A: Firstly support reactions should be calculated and then shear forces and bending moments should be…

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.