Draw the influence line for member BC and interpret the diagram. H 15 ft A B. 4 @ 20 ft = 80 ft-

Q: classify the truss, and find the bar force. and reaction SF ANNA 8G? 10@ 30' 300' M 200k K* 40' 30'

A: IntroductionA truss is a type of structural framework made up of triangle-shaped pieces joined at…

Q: SOLVE the location of the Centroid from column ABC

A: Given data in question  Frame Point loads Span member lengths  Uniform columns   To find out…

Q: 20 IN H 1=3 m 3 d 1=3 m 1-3 m Which of the following most nearly gives the force in member cd due to…

A:

Q: AT

A:

Q: A B с 4m D 4m 4m 187,5 202,5 197,5 A 192,5 B -6m D C -6m Calculate the magnitude of the force acting…

A:

Q: Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming…

A:

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: Determine the magnitude of force in member BD

A: Find the magnitude of force in member BD

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

A:

Q: Construct the influence lines of each truss member. H 4 m В E 6@3 m = 18 m

A: An influence line for an obtained member, like reaction, axial force, shear force, or bending…

Q: Hinge A Plate 1.2 m. F 1.2 m x 1.2 m) B 30 Container liquid

A: To find force on gate AB

Q: Q.2) For the truss shown in figure below, determine the forces in lo00 4. 2000 N LE 4. in 3m 3m 3m…

A:

Q: 3 m A B 3 @ 4 m = 12 m LOAD W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 90 15 110 Draw the…

A:

Q: determine the resultant of the forces indicated

A: Calculation of Resultant Force of Given Forces ###

Q: For the reinforcement shown, whose inclined force of 40 kN is applied in the same line of action of…

A: (a) Zero Force Elements: At a unloaded joint, when there are three elements meet out of which two…

Q: Problem 2 The truss shown carries the following uniform live load and concentrated live load. E F 3…

A:

Q: 2. Compute the shearing stress in the pin at B for the member supported as show the given figure.…

A: Given- Diameter of Pin (d)=22 mm

Q: In the rigid frame shown in figure, a central concentrated load is acting on "BC". Find slopes e, 0…

A:

Q: RAH A 60⁰ RAV 500 N E 60° 3m 60⁰ RAV = 106.2 N O O RAV = 201.8 N O RAV = 365.72 N RAV = 123.5 N C D…

A:

Q: Find the member forces and reactions for the truss with loading shown.

A: Given -  To find -  Find the member forces and reactions for the truss with loading shown.

Q: AM IS SUPPORTED BY A PIN AT A AND WIRES P ON THE BEAM CAUSES THE END C TO BE DISP WARD, DETERMINE…

A:

Q: Solve support reactions. note: there is an internal hinge at C

A: ##Calculation of Support reaction ###

Q: B 0.75 m 55⁰ A 1 m 0.5 m 50 N 75 N-m

A: Given values: Consider the given structure and draw the free body diagram to calculate the unknown…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. FAH 2 m 25KN FAV What is…

A:

Q: THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE…

A:

Q: PL Find the Forces members BD, CD eud CE in

A:

Q: a. Determine the degree of indeterminacy b. Select vertical reactions at C and E as redundants. Draw…

A: Consider the given beam.

Q: Determine the magnitude of the pin force at B. 0 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A: To find out the magnitude of the pin force at  B.

Q: 10 ft 12 ft D E 60 k Pins at B and D 16 ft Fixed at A Pinned at F F - 8 ft A Prob 5) Solve for the…

A:

Q: Find the support and bond forces

A:

Q: The truss shown carries the following uniform live load and concentrated live load. F 3 m A В 3 @ 4…

A:

Q: Find the force in the member BC * 4 kN 2 kN By C 60° A 60% 60° 60° D E ARD 3 m 3 m RAF

A:

Q: Compute the total reaction of the frame at Joint B.

A:

Q: 2. Determine the magnitude of the pin force at B. 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A:

Q: Leads P and R are applied at the fre end of the post having a diameter d shown in Fig. P9.66.…

A: Consider the given figure as follows:

Q: Determine the member force on member FI

A: Determination of force in member FI###

Q: Solve for the support reactions and draw and label the SFD and BMD

A: The given beam is shown below:

Q: Im 3m 3m SOLVE FOR ALL THE FOKES IN Im EACH MEMBER RADIUS OF PULEY = 0. Tm 2m 700 KN

A: When an object encounters another object, it experiences a force that pushes or pulls. When…

Q: Q2- Determine the magnitude and direction of the resultant force acting on the corbel ? see figure…

A: The resultant force is the total magnitude of vertical and horizontal forces. If a force is inclined…

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.