Draw the equivalent circuit of a 10 KVA, 1860 / 400 V 1-phase transformer with R1=0.4 ohms, R2=0.03 ohms, X1=1.2 ohms and X2=0.07 ohms. Also calculate the equivalent resistance and reactance referred to primary winding. Equivalent resistance Equivalent reactance

Draw the equivalent circuit of a 10 KVA, 1860 / 400 V 1-phase transformer with R1=0.4 ohms, R2=0.03 ohms, X1=1.2 ohms and X2=0.07 ohms. Also calculate the equivalent resistance and reactance referred to primary winding. Equivalent resistance Equivalent reactance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Design a lo power transformer to be used in a wind turbine for the following specifica tions: 1-…

A: To need to design a power transformer that is to be used in a wind turbine for the following…

Q: 6. The figure below shows a single-line-diagram of part of a power system. For each transformer in…

A: For a power system, The single line diagram is shown below,

Q: Q.1: The following data refer to a single-phase trans former: Turn ratio (2:1). R1=2.4n, X-5.5 n.…

Q: Question 5 An ideal transformer is one which has Not yet answered No losses and magnetic leakage…

Q: Below is a time current curve (TCC), showing the damage curve of a transformer. Draw (roughly),…

A: TCC- Time Current Curve is a plot shows the overcurrent device's interruption time which is based on…

Q: A transformer has a turn ratio of 1: 10. A resistance of 2000 ohms is connected across the secondary…

Q: A 400/200 V, single-phase transformer has primary winding resistance of 0.20 and secondary winding…

A: Given a 400/200 V, single phase transformer has, Primary winding resistance, R1=0.2 Ω. Secondary…

Q: DC 200 V is applied to the primary of a transformer with a conversion ratio of 1/5. From secondary…

A: The winding functions as a short circuit through the source terminals of DC when a DC voltage is…

Q: In transformer, loss that is related to ohmic resistance of winding is

Q: What are advantages of transfering parameter from 1 side of transformer to other side? Subject…

A: The advantages of transferring parameter from 1 side of the transformer to the other side are 1.…

Q: the circuit shown in the figure, a voltage with a peak value of 212.16 V is applied to the input of…

Q: The open-circuit voltage of 242 V and the full load secondary voltage of 234 V, then the %…

Q: A 50 KVA, 4,400/220 V transformer has r1 =3.54 ohms r2=0.009 ohms, x1 =5.2 ohms and x2 =0.15 ohn…

Q: In transformer, the eddy current loss can be minimized by using thin size copper conductors using…

A: Transformer have 2 types losses In the question the eddy current losses can be minimised by???

Q: The primary of a current transformer takes 1 A at a power factor of 0.4 when it is connected across…

A: Given: N1=2N2Io=1 Acosϕo=0.4I2=50 Acosϕ2=0.8 lag

Q: In transformer, the eddy current loss depends on both frequency and flux density load current only…

A: The circulating current produced in the body of the magnetic material when it is subjected to an…

Q: A single-phase transformer has maximum efficiency of 98 %. The core losses are 80 W and the…

A: Given: A single phase transformer has Maximum efficiency, ηmax=98 % Core loss, Pi=80 W Equivalent…

Q: The resistance and reactance of the primary winding of a 440/110 V single phase transformer are 4.4…

Q: Josses = losses 1. Maximum efficiency of transformer is when 2 At maximum efficiency load current…

A: SOLVE PROB.

Q: a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic…

A: Duty cycle : Duty cycle in the power system is defined as the ratio of the time during which a load…

Q: A 1150/140V, 50 HZ, 1-phase transformer with cross sectional area of the core is 34 cm2 and maximum…

A: From the Transformer induced voltage expression

Q: In no load Phasor diagram of practical transformer, the core loss current Ic is with primary voltage…

A: When a transformer is on no-load, the secondary is open circuited. Hence secondary current is zero.…

Q: A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current…

A: Given, A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. The exciting…

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

A: In this question, Choose the correct options What is power factor to become zero voltage…

Q: A 50 kVA transformar has a core loss of 500 W and full load core loss of 900 W. The load at which…

Q: A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase.…

A: Scott connection is used to convert a balanced three-phase into balance 2 phases or vice versa. It…

Q: 1. An ideal transformer with a 450 turn primary connected to a 600 V, 60 Hz supply line needs to…

A: Number of turns in primary N1=450. Primary voltage V1=600 V. Secondary voltage V2=240 V. Load…

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

Q: In a transformer the core loss component is 90 degrees with the flux Select one: O True O False

A: Given: Core loss component . In no load condition of transformer ,the secondary is open circuited…

Q: Ideal transformer core has permeability equal to Select one a Non-zero finite c. Negative G Intinite

A: Ideal transformer core has permeability equal to

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

A: The voltage regulator is required to maintain voltages within the permitted range that the…

Q: The losses found in a transformer

A: There are two types of losses that occur in the transformer. 1. Core loss 2. Copper loss Apart from…

Q: What are the advantages of Delta connection in high power transformer?

A: Transformer : It is an electrical device used to transform the voltage from one level to another.…

Q: The purpose of the no-load test in the transformer is to determine O Input voltage O Core loss…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Draw the equivalent circuit of a 10 KVA, 1860 / 400 V 1-phase transformer with R1=0.4 ohms, R2=0.03 ohms,
X1=1.2 ohms and X2=0.07 ohms. Also calculate the equivalent resistance and reactance referred to primary
winding.
Equivalent resistance
Equivalent reactance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following are power losses that can occur in a practical transformer (non-ideal)? copper loss O loss due to eddy currents V hysteresis loss O voltage drop due to coil material
A transformer has a turn ratio of 1: 10. A resistance of 2000 ohms is connected across the secondary terminals. The resistance offered to the current in primary winding will be
Tansformers
14. The maximum flux of a 50H2 transformer is 0.001Wb. If the primary is wound Vwith 1080 turns, find the applied primary voltage and then calculate the number of turns required for a 15V secondary. Ans: N2=67
6. 150 kVA, 2800-240 V, 50 Hz transformer. Regis = 0.0082N , Xeq.Ls = 0.0223N RfcHs=2200N Step down transformer delivers 135 kW to a load at 0.9 lagging power factor at rated voltage. Determine the Following: a) Terminal voltage (LV side). b) Terminal voltage (HV side). c) High side current. d) Input impedance. e) Voltage regulation. f) Efficiency. g) Voltage regulation for 0.9 leading pf. h) Draw the phasor diagram of secondary circuit at 0.9 lagging pf. i) Draw the phasor diagram of secondary circuit at 0.9 leading pf. XmHs=12002
The full-load copper loss of a transformer is 1600 W. At half-load, the copper loss will be O a. 1600 W b. 6400 W O c. 400 W d. 800 W 4 11
Calculate the primary leakage reactance of a transformer, supplying a load current of 10 A and 60 Hz. The transformer has a primary winding of 200 turns and secondary winding of 100 turns. The primary leakage flux has a peak value of 2 mWb and primary current is 5 A. BI Fr T: II
A 50Hz, single phase transformer has a ratio of N2:N1 = 0.2. On full-load, the secondary current is 200A. The resistance and reactance of the primary winding are 0.8 ohm and 4 ohm respectively. The corresponding values for the secondary winding are 0.04 ohm and 0.1 ohm. If the secondary is short circuited, what voltage must be applied to the primary to produce full-load current? What will be the copper loss?
Find out the equivalent inductance for the combination when 2 inductances L1 and L2 are connected in parallel such that their fluxes oppose each other Determine the efficiency of the transformer and find out the value of load at which efficiency will be maximum 3
Which of the following is the correct equation for calculating the rated current for a single-phase transformer? A. I=va/e b.I=sc/e c.a/e d.e×z/e
A short circuit test performed on a 25 KVA 2300/230 V transformer gives the measured value of the resistance as 0.8 Q and 0.009 Q on the two sides of the transformer. The total equivalent resistance in Q referred to LV side will be
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3-phase side. The main transformer primary to secondary turns ratio is (12/1).