Draw a power supply based on a 2x9V efficient mid-point transformer and a full-wave rectifier plus filtering. If the diodes each have a waste voltage of 0.7V, what will be the maximum voltage of the capacitor? What is the purpose of a zener diode? Give its electrical symbol. We use two cables of length 1 = 2 m and of section s = 10 mm² to start a vehicle whose battery is discharged, linked to a battery of 12 V of a second vehicle. Calculate the available voltage for a starter of a petrol vehicle requiring 100 A and a diesel vehicle requiring 250 A. Which conclusion can you give? We give the conductivity of the copper wire y = 6.107S.m-1.

Draw a power supply based on a 2x9V efficient mid-point transformer and a full-wave rectifier plus filtering. If the diodes each have a waste voltage of 0.7V, what will be the maximum voltage of the capacitor? What is the purpose of a zener diode? Give its electrical symbol. We use two cables of length 1 = 2 m and of section s = 10 mm² to start a vehicle whose battery is discharged, linked to a battery of 12 V of a second vehicle. Calculate the available voltage for a starter of a petrol vehicle requiring 100 A and a diesel vehicle requiring 250 A. Which conclusion can you give? We give the conductivity of the copper wire y = 6.107S.m-1.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
1) How is the diode and zener diode in the electronic circuit and how they work?indicate the differences between them.2) Can a zener diode be used instead of a regular diode? please explain.3) Is it to step down and rectify the 220V AC signal by means of a transformer or to convert 220 V?rectify it and then reduce its value to the desired DC level using a voltage divider circuit?suitable.?4) Bridge type full wave rectification with two diodes full wave rectification using a medium ended transformerCompare the rectifier circuit and list its advantages and disadvantages relative to each other.5) What is the concept of PIV (Peak Inverse Voltage) for rectifier circuits?For which rectifier circuits is this value more important?
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
An ac voltage source with a peak value of 20 V LUK is a silicon doped diode and a 500 ohm resistor is connected in series in the circuit. The forward direction resistance of the resistor in D phase is 10 ohms. A) the highest current value through the diode B) Calculate the output voltage when the welding voltage is at its maximum level. C) If the diode is considered ideal, repeat steps a and b.
14.3 V Answer the following questions, since the minimum voltage value to transmit the zener diode in the figure given above is 9V and the power of this Zener diode is 0.3 watts. a) draw a parallel Clipper circuit that will give the output signal given in the figure. b) enter the name of the parallel Clipper circuit that will give this output voltage.