Control system Draw a block diagram representation of a thermostatically controlled electricoven in the kitchen of a home.zising Masons formula find outI(S)T. F.Electric powerinput↓1SOLUTION:DesiredtemperatureinputThermostatE(S)ActualmeasuredtemperatureElectricheaterThermalsensorH(S)Actualtemperatureoutput-y(s)

Manson's formula:-transfer function TS= where k=1,2,3..............nn=number of forword…

Draw a block diagram representation of a thermostatically controlled electric oven in the kitchen of a home. using Masons formula find out. I(S) T. F. Electric power input SOLUTION: Desired temperature: input Thermostat E(S) 헬 Actual measured Electric heater Thermal sensor Actual temperature output y (s)

Draw a block diagram representation of a thermostatically controlled electric oven in the kitchen of a home. using Masons formula find out. I(S) T. F. Electric power input SOLUTION: Desired temperature: input Thermostat E(S) 헬 Actual measured Electric heater Thermal sensor Actual temperature output y (s)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter7: Alternating Current, Power Distribution, And Voltage Systems

Section: Chapter Questions

Problem 5RQ

See similar textbooks

Similar questions

GENERAL RLC CIRCUITS: Solve and show your solution completely. Make sure your answers are in 4 decimals places. The ohmic resistance of a large magnetic contactor is measured to be 20 ohms. A 230 V 60 Hzis impressed upon the contactor and the current is taken as 3.2 amperes. Neglecting core loss,determine the inductance of the contactor in mH.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.1 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=150 Volts, Time period is 15 milli seconds and =50 degrees. Vp t = 0 Ф II
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
2. A burst controlled triac is feeding a 200 ohm resistive load. The AC supply providing 240 V rms voltage at 60Hz. a) For one cylcle on, four cycles off control calculate the load rms voltage, current, power transferred to the load and efficiency. b) For four cylcles on, one cycle off control calculate the load rms voltage, current, power transferred to the load and efficiency.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
Q9 / What are the function of brushes , pole and commutator in DC machine
Ip Ep=40 V f = 60 Hz N₂= 20- N₁ = 120 Find the maximum flux om om = Find the magnitude of the induced secondary voltage Es Es = units + Is Es units If the coefficient of coupling (k)= 0.75, determine the magnitude of the induced secondary voltage Es Esk=0.75 = units
Find the margin of K to keep the system shown in figure N°1 stable
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 100 Volts at 1.3 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and o =50 degrees. Vp Ф
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
1 In the system shown in the below figure, the switch is closed at t = 0. a Determine voltage reflection coefficient at the load and the source b. Sketch the bounce diagram of the VOLTAGE and the CURRENT and give sufficient information on it (up to 4us) C. Sketch diagram of voltage and current at source and load Mittetu Md. Calculate the steady state Vss. Vss and Iss. Iss opinti 15 Wan httons e. Find the value V(z-50m 1.7us) TERS Wertens atom Dett th will MARRI E yo w B pinn WERS THIS Suprin 90 MAKEL R₂=90 0 3 CAP 180. Rr = 180 Q - i T Mart 1800 H SUS Vg=90 V HIE 1 D = min 200 thin 1 FARG - Bilare. Radio T 149 SATISH SET Pan PARACHUNG G IN Sulta Ap 135 aytinius - FORES exotic Me GALER 2 Mer t=0 400 NITINE atas Aper SUMB satan THE SIM- " WAS Thy POST ANE nicht www.M upp 6 HIS 328 20 p Hifiq Z. = 60 52 WHAT p=10m/s 459 w 30 Patie SATE 108 1 = 100m MNA A
The effect/effects of increasing the damping ratio 5 of a second-order system is/are O a. The maximum overshoot decreases and the damped frequency decreases O b. The settling time decreases and the peak time increases O c. The maximum overshoot increases and the damped frequency decreases O d. The settling time decreases and the peak time decreases