Directions: Find the volume of each figure. Round to the nearest hundredth when necess 1. 2. 9 m 7 m 6.4 in 5 m 3.6 m 14 in 17.5 in 10 m 3. E13 mm – 4. 15 cm .28 cm 25.7 cm 19 mm 20 ст 37 cm 6. 8 km 7 ft 3.2 km- 25 ft 18 ft 7. 11 m 8. 4 in 12.7 m 14 m 9 in 16 m 9.5 m B = 41.57 in? 5.

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: A Contractor/foreman needs lumber to be used for wooden scaffoldings, the set of lumber can be…

A:

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: 1500 liters/s of ammonia gas at 100°F and pressure of 30 in.Hg has a specific heat ratio of 1.304.…

A: Given data Q=1.5 m3/sT1=100°FT2=180°Fγ=1.304 Here, Q is the flow rate and T1 is the initial…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: Please give the answer as in the format asked

A:

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: need answer in 15 minute's please 3 (29// A ruck is throw up according to equation s(t) = { +2E-6t…

A:

Q: can tutor continue the next two questions also

A:

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: A gas has an initial temperature of 25 degrees Celsius. It is cooled until its temperature reduces…

A: final temperature = 22.5o CExplanation:Approach to solving the question: Detailed explanation:…

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: The question is not answer fully. Please answer the second part of the question statement.

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: Which of the following statement is NOT correct? Fluid Mechanics is the study of the behaviour of…

A: Mechanics is a branch of science which deals with the forces and its effects like deformation,…

Q: Write legibly and box the final answer

A:

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.

Q: Which of the following is the front ?view of the figure

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.