Diameter - 40 cm force- 4000 N Determine pressure ?

Q: If the manometer is open to the atmosphere, what is the pressure at C water (p = 1.0 g/cm³) A ct B…

A:

Q: re of water in a pipeline by means of a simple m mercury. The mercury l s 160 mm higher than t ne…

A:

Q: Convert each temperature. -109 °F to °C (temperature of dry ice)

A: Convert -109°F into °C of dry ice temperature. The following equation is used to convert the given…

Q: At which depth under water the pressure equal three times atmospheric pressure.

A:

Q: If a heavy cargo is lifted using a ship's crane and the load remains suspended within the ship, what…

A: When the heavy cargo is lifted using a ship's crane and the load is still suspended within the ship,…

Q: The cylinder shown in Figure 2 is made from uniform material and placed in kerosene at 25°C. i)…

A:

Q: holds 0.7ft3 of water. Filling up the tank requires how much water? a. 0.18 in3 b. 0.78 in3

A:

Q: Situation 1 - The pressure on a closed tank reads 58.86 kPa. What is the equivalent height, in…

A:

Q: 1. For the shown hydraulic jack the gage pressure indicates 140 kpa how much kilograms should be…

A:

Q: 6. One leg of mercury U-tube manometer is connected to a pipe containing water under a gage pressure…

A: Specific weight of water = 62.4 lb/ft3  Specific gravity of mercury = 13.6 From Pascal's law of…

Q: What is the ºAPI if the specific gravity at 15.6 ºC is 0.928?

A: specific gravity Sg = 0.928 @ 15.6o C To determine:

Q: If the pressure at A was 78 kPa, what is the pressure at B?- Note all dimensions are in cm. Water…

A: Given data:  The pressure at point A is PA=78 kPa The density of the mercury is ρm=13.6×103 kg/m3…

Q: What is the pressure at 61, 500 ft in SI.

A:

Q: If a depth of liquid of 2m causes a pressure of 20 kpa, what is the specific gravity of the liquid?…

A:

Q: Indicate whether the statement is true or false. a. Air is compressible b. Oil is compressible c.…

A: It is required to choose correct answer

Q: What is hydrostatic fluid

A: Hydrostatic fluid is the branch of fluid mechanics in which the fluid is at rest in stable…

Q: Question 3 A Mcleod gauge is used for measurement of very low pressure in scanning electron…

A: Step 1Calculate the density of mercury ρmercury : ρmercury  =  SGmercury ×  ρwater ρmercury  =  13.8…

Q: For a given certain bearing bore dimensions (1& d), the number of variables that are under the…

A: Option 'C' is correct. For bearing design there are total five parameter that matter. These…

Q: Differentiate between gage and absolute pressures

A:

Q: What should be the working pressure of a cylinder with 3 in. piston diameter so that it can balance…

A:

Q: a,b,c please and thank you!

A: The objective of the question is to determine the maximum and minimum principal stresses and the…

Q: 3. A 5 kg object has a volume of 1000 cc. What is it's specific weight in lbf/cubicft? 4. What is…

A: Find the specific weight and specific gravity.

Q: ight has a vo

A:

Q: What is the ºAPI if the specific gravity at 15.6 ºC is 0.925?

A: Given : specific gravity Sg = 0.925 @ 15.6o C

Q: A oil of specific gravity 085 determine the density of the oil. Fluid question.

A:

Q: Calculate the pressure difference between A and B.

A:

Q: Convert the following readings of pressure to kPa absolute, assuming that the barometer reads 760 mm…

A: Given- 18 in. Hg vacuum = 0.4572 m.Hg vacuum (Gauge pressure)  Barometer reading atmospheric…

Q: How far below the water surface (in m) should the center of a vertical square 1.5 m on a side with…

A:

Q: The pressure of air in the air receiver is 1035 kPa and has a 4450 N force. Determine the piston…

A:

Q: The pressure of steam inside a boiler is shown by a pressure gauge 120 N/cm2. Take barometer reads…

A:

Q: At what depth below the surface of the oil, relative density 0.89 will produce a pressure of 120…

A: The given data are: Here, d denotes the relative density and P denotes the pressure.

Q: What is the specific weight in kN/cu.m of an oil with specific gravity of 0.91? (UP THREE DECIMAL…

A: GivenS.G=0.91

Q: An unpressurized square tank with a 5-meter width holds a 5-meter column of seawater (SG=1.03). What…

A: Given:Width of the tank, w= 5 mHeight of water column, H=5 mSpecific gravity of water, SG=1.03

Q: If a depth of liquid of 3m causes a pressure of 15 kpa, what is the specific gravity of the liquid?…

A:

Q: A cylinder contains a fluid at a gauge pressure of 350 kN m-2. Express this pressure in terms of a…

A:

Q: QUESTION 2 By using Figure 2, calculate the pressure at Point A. Given SG oil 0.85 and SG mercury…

A:

Q: 5. Two vertical cylindrical storage tanks are full of liquid water, density atmoshere. One is 10 m…

A:

Q: Determine pressure due to water at depth of 13 m on a body

A: Given data : Density of water=ρ Depth=h Acceleration due to gravity=g   To find : Pressure

Q: The specific gravity of steel is 8.89. What is the volume in ft of a steel ingot weighing 8650 kg?

A:

Q: 1- Calculate the specific weight (Y), density and specific volume of one liter of liquid its weight…

A: given mass of liquid m=70g=0.07kgvolume of liquid V=1ltr=10-3m3

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.