Determinethe magnitude (lb) of the horizontal component of force at point C if P = 150.5 lb, x = 13.6 in, y = 6.8 in, and z = 8.3 in.

Q: Resolve the horizontal 660lb force as per figure below into components acting along the u and vaxes…

A:

Q: Q1: The 700 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A:

Q: Determine the magnitude of the resultant R for the F1 and F2 combination. b) Where should the…

A:

Q: The X-component of the force P is 140 lb where force P is going to the upper left with a slope of…

A:

Q: he third force so that the resultant of the three forces is vertically downward with a magnitude of…

A:

Q: Current Attempt in Progress Determine the scalar components Ra and Rb of the force R along the…

A: According to the given data θ=114 ϕ=22 We need to find Ra Rb and Pa

Q: At what angle 9 must the 300-lb force be applied in order that the resultant R of the two forces…

A:

Q: Determine the resultant of the concurrent forces shown in the figure below. A = 7003 N, B = 2502 N,…

A:

Q: The force P = 2 kips is applied to point A, and is supported by cable AB, cable AC, and bar OA. The…

A:

Q: If the resultant of the forces shown passes through point A, determine the magnitude of the unknown…

A: The diameter of the pulley,

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A:

Q: Two forces X and Y act vertically downward directly at points D and F respectively while force Z…

A: We will consider joint F into equilibrium.

Q: point A towards O, determine the magnitudes of the resultant force and forces Fg and Fo Set the X =…

A: Given that: Cable AB and AC are fixed to support the 2000 N load which is acting along negative z…

Q: ERTICAL POST IS SECURED BY THREE CABLES. THE CABLE ARE PRE-TE AT THE RESULTANT OF THE CABLE FORCES…

A:

Q: Find the resultant of the applied forces acting on the billboard support frame and locate the line…

A:

Q: What is the magnitude of the resultant force caused by the three forces below? Assume that a, = 50°,…

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…

Q: 1.500 kN/m 0.750 m 65 1.500 m 2.75 kN 225m 1.500m Refer to the diagram. ACD is a rigid member.…

A:

Q: Determine the Resultant of the Torces 1250KN in the 726 KN System below. Дие

A: This question is based on the concept of classical mechanics.

Q: The cable AB prevents bar OA from rotating clockwise about O. if the cable tension is 750N,…

A: Tension in the cable is 750N θ1=60° Using sine law…

Q: 1. A 5kN force is applied to the pulley system as shown. The member OA is a simple two force member.…

A:

Q: Q2(30%) Determine the resultant of forces system shown in Figure and locate it with respect to point…

A:

Q: Find the resultant for this system of forces: C F2= 81 lb

A: calculate the value of x,x=72+42x=8.062 ftnow angle θ is,tanθ=x4=8.0624θ=63.6ocomponent of F2 in…

Q: A 1. 3' Determine the x and y components of the forces at A, B and C when M = 5000 in-lb. Y 1 L--x…

A:

Q: 400 lb 6 pies - A' B 4 pies C 4 pies E D' 8 pies

A:

Q: Q2. Replace the force system acting on the frame by an equivalent resultant force and specify where…

A: Solution:

Q: Determine the height h above the base B at which the resultant of the three forces acts. 20" 560 lb…

A:

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

A: Given data: F1=350 lb F2=660 lb F3=520 lb a=5.4 ft b=2.9 ft c=4.0 ft θ=50o

Q: The metal plate is held by two cables as shown in the following figure. If the force of each cable…

A: Given FAB=900lbFAC=200lb

Q: Q1: The 650 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A:

Q: Q3) For the concurrent coplanar force system shown below, calculate the magnitude and the slope of…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: C2X8 X Given the 50 lb. force at point A, replace it by a force acting at B. B 50# A

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.