Determine: Use 3 decimals a) The width of the base b) The value of cut at station B if it has an area of 16.82 sq.m. b) The Volume of A and B with prismoidal correction (use end area method)

Q: Please draw the steps in doing profile leveling using the date given. Please provide proper…

A: Given Data, Bm ---bench mark  Tp- Turning point  Bs -- Back sight  Is -- intermediate Sight…

Q: A Find by Section Method and Join Method: 3 B Hawe Bridge 50 3′ E D 50 3 F G 50 3' H A

A: To find the member forces in the given truss by both methods.

Q: We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is…

A:

Q: 3kLf 20 ft eliste Max = Max

A:

Q: Draw the Y and M 6m 15 31² diagram 20 kN/m 6M 3j+c 20 amer= so kn эм

A: Given: A frame  Required: Shear force and bending moment diagram

Q: A straight line AB 100 mm long is inclined at 45° to VP. End B of the line is 30 mm aboveHP and HT…

A: Length of line AB = 100 mm AB is inclined at 45o to VP. End B of the line is 30 mm above HP…

Q: 8. Find the particular solution of the following DE. a. D - 2D- 3)y 0; when x 0, y = 0, y -4. b. D2…

A:

Q: PROBLEM 4: Given: b = 300mm, d = 450mm, As' = 2D25mm, d' = 65mm, fc' = 28MPA, a 415MPA. Solve for o…

A:

Q: 2

A: Step 1:Step 2:

Q: What is Shape Correction Factors For Alpan (1964) Method ?

A: Alpan method (1964) It is based primarily on peck and Terzaghi method (1948). It evaluates the…

Q: 1. 9y"-12y'+4y = 0 2 -X 2 X- Ans. y=c,e³ +c2xe³

A: NOTE - Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Simpson's 1/3 Rule can only be applied when the number of segments or strips used to approximate the…

A: Answer:- False Explanation:-In order to apply Simpson's 1/3 rule the number of segments must be odd.

Q: MOMENT AREA METHOD FIND THE SLOPE AT POINTS B & C E= 200GPA I= 360x106mm4 5m 10KN A 10m

A: Moment Area Method: Given: E = 200GPa=2 x 105 N/mm2 I = 360 x 106 mm4  EI = 7.20x1013 N mm2

Q: The cross section at station 2+60 has a cut area of 9 ft2 and a fill area of 4 ft2 and the cross…

A: Cut Area of the cross-section at station 2+60,A2+60=9ft²Cut Area of the cross-section at station…

Q: For the following set of Stadia notes. Rod Interval (m) = 3.23 Horizontal angle = 85° 23' (measured…

A: Given:                       Rod interval = 3.23 m              Horizontal angle = 85∘23' {Reference…

Q: Wo> pa WIOX 30 18' Find: Centerline spacing = a if p: .6 V : 18 Ksi

A:

Q: The stress of a structure is shown in the figure below. Assuming that the El of the entire beam…

A: To determine:SFD and BMD of frame-Moment distribution method is used for the analysis of frame

Q: 1) choices: 5.19 8.19 7.82 6.32 2) choices: 116.5 140.3 192.83 101.99

A: To Determine Y bar  Moment of Inertia about x axis

Q: Step - by - step process please

A: Given data in question  Moment value in vector form Lever arm in vertor form To find out  How to get…

Q: Question: IdE 525521.12 N:313813.5741 E:525621.124 YN 313813.5741 6 E-525521.12... What is the area…

A:

Q: Find the work done Force on crate%3D4 N Dispalcement=1 m

A: Introduction : The given question is related with mechanics . We are provided with value of force…

Q: Backsight Intermediate Foresight Rise Fall ReducedLe Top Sight 1.250 0.300 0.450 0.520 0.515 0.526…

A: To approach solving questions related to identifying contour lines or similar data interpolation…

Q: Simpson's 1/3 Rule can only be applied when the number of segments or strips used to approximate the…

A: Answer :- False Explanation:- In order to apply Simpson's 1/3 Rule the number of segments or strps…

Q: 2P A SI 4I 2.5m 25m 1.25m 2.5m 1-25m

A:

Q: = 3.086 GA Cm ,2.914 Cm 1,-1. Scm TOP most £ Lcft most Bottom most E Right mast Reference Reference…

A:

Q: Station A (10+040) 9.50 11 +3.00 +2.00 +4.00 Station B (10+060) 6.50 8.00 +1.00 1.20 +2.00

A:

Q: Calculate vertical components at point C

A:

Q: -r = 100 mm 50 mm

A:

Q: Corrections A(channel)=9,400mm² A(wide-flange)=62,200mm²

A: Answer  (2a) Calculation of location of the centroid of built up section from top To calculate the…

Q: The following offsets are taken from a chain line to an irregular boundary towards right side of the…

A:

Q: QUESTION 13 The readings shown below were taken to find the height of A, B, C, D, E, F, G and H. a)…

A: To Determine :- a) The adjusted reduced levels for all the pegs. b) The difference of height between…

Q: where did the highlighted part came from?

A: Given: Measure length of line = 2538.45m  Length of tape = 45 m  Required: To explain the…

Q: Determine the location of centeroid of the following figures: 6" 3.5" 2-in.-diameter hole 2" 2" es)

A:

Q: (Q3) Compute the angle (B) in the below drawing, if aAB=36 45'23" and the magnetic declination is…

A:

Q: Find the internal force 291.1 mmm. A D0₁ = 41. Tay= 220mm =50N B www.lbl ↓ TOON 02-623 ·100mm- 540…

A: Given truss with vertical load=100 N and it is asked to determine the internal force in each member.

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).