Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller spherical portion removed. hemi- Ans. x = 45 R 112

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: i cant read this.. can you write it out??

A:

Q: not read the answer. Is there a way to upload it in ano

A: Navier-stokes equation (momentum and continuity equations)

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: 3.00- 1.25-

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: 5m %3D d=9·8\ mls? १त्र वह w Given data

A: Given data : The value of mass=m The value of acceleration due to gravity=g The value of height=h…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: 9. In a factory, packages are moved from a room on the second floor to a station on the first floor…

A: COEFFICIENT OF FRICTION DEPENDS ON MATERIAL

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: or columns should be the sum of when we place integers starting from 1 in a magic square of size…

A:

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the…

A: Weight of full spool = 2038=1638 ouncesEmpty Spool weight = 114 = 108 ounces

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: 1. show all steps in detail, units and formulas please.

A:

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: Is this definitely correct? A few calculators online such as BMEP calculators give me a different…

A: Given data:Torque = T = 100 NmEngine is four stroke,so there is one power stroke after two…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: cm ỏ i 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft…

A: Smallest division of main scale =0.1 cm  Number of division in vernier scale =10  Least count =…

Q: name these lines

A: The names of the given lines is given below.

Q: why have you writen the answers in mm. when all the length are in meters

A:

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 5.5m x 6.2m x 7.7m x 4m x…

A: given; dimension of irregular shape of sheet metal;          (1m=39.3701inch)L1=5.5m=5.5*39.3701…

Q: . Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: According to the given details provided, we need to identify the view on the right that shows the…

Q: 3. Water is flowing in a pipe with radius of 25.4 cm at a velocity of 5m/sec at the temperature in…

A:

Q: An exponent, such as the 4 in the expression 94, means: the number of times the number before the…

A: It is required to determine value of 94

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.