1. A railway embankment is made level for 180 m. the ground has a uniform slope of 1 in12. The formation width is 9 m and the side slope is 2:1. The ground is level across thecenterline of the embankment. Determine the volume of the embankment if the highend terminates vertically. (Take 10 intervals)

Slope: - It is defined as the ratio of vertical change to horizontal change in a given distance.

Answered: Determine the volume of the embankment

Engineering

Civil Engineering

Determine the volume of the embankment

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.28P

See similar textbooks

Related questions

Q: CONJUGATE BEAM METHOD. 200 lb 400 lb B 38- 4 ft- -1.0 ft

Q: Determine the shear force 7.36 ft to the right of point A for the beam shown belowif T = 1108 lb ft,…

A: Given data in question Span member length Concentrated moment UDL UVL To find out Shear force

Q: The beam shown left below has the cross section shown right below. Determine (a)The maximum tensile…

A: Maximum shear stress and bending stress can be calculated after we get the value of the maximum…

Q: Determine the shear force 13.54 ft to the right of point A for the beam shown belowif P = 553 lb, Q…

Q: 3 A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of…

A: 8. Given:- P=60kN L=200mm change in length =0.09mm To find:- poisson's ratio and threee modulus of…

Q: Determine the shear force 10.97 ft to the right of point A for the beam shown belowif T = 1012 lb…

Q: 3) What is the difference between? 2-Internal and External flow

A: Internal flows are the flow of fluids surrounded by solid surfaces. For example Water flowing inside…

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

A: Given data Modular ration (m) = 20 b = 4 in. w = 252 lb/ft L = 19.3 ft B = 6 in D = 10 in…

Q: Calculate AH for the process in which 50.0 g of water is converted from liquid at to vapor at 25 C?

A: Given data: Mass, m = 50 g Specific heat capacity for water, c = 4.18 g-1 Change in temperature from…

Q: Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/h at 25°C. The…

Q: the average shear stress in the bolts must be limited to 27 must support an applied load of etermine…

A: Given:Average shear strain=27 ksi,z=27 ksiNumber of bolts,n=5Applied load,P=2600 lb

Q: Design an isolated rectangular footing: P(dead load) = 225 kN P(live load) = 130 kN Qa = 180 kPa Df…

Q: Situation 4: A W6x25 has a length of 5.3 m. Fy= 248 MPa. The properties are given below. Properties…

A: Le = kL = 0.8 x 5.3 m = 4.24 m = 4240 mm

Q: If the shear at point A on a beam is zero, then A.the slope of the bending moment at A must be zero…

Q: Given the properties and dimensions of an isolated spread footing, solve for the ultimate axial load…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: Describe the process of being certified and trained, using concrete examples from your own personal…

A: Training involves imparting skills and expertise of any sort to the trainee. While certification is…

Q: Determine the bending moment 7.59 ft to the right of point B for the beam shown belowif P = 505 lb,…

A: Given data in question Load Span member length To find out Moment at 7.59ft right of point B

Q: A weir in a horizontal channel is 12 ft wide and 4 ft high. The upstream water depth is 5.2 ft.…

A: Width of the weir = 12ft Height = 4ft upstream water depth = 5.2 ft Elevation of the water surface…

Q: SHOW COMPLETE & DETAILED SOLUTION W/ FBD The shaft is hollow from A to B and solid from B to C.…

Q: Problem 01 Determine the critical buckling load for each of the columns, using the Euler equation =…

Q: 2. Using the conjugate beam method, determine the maximum deflection of the beam. Use E = 10,000 ksi…

Q: A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if…

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

Q: Use Castigliano's theorem (the least work theorem) to analyze the structure shown. Calculate the…

A: Given: A symmetrical frame. Required : Analyze the structure using Castigliano's method and to find…

Q: venturi meter with a throat diameter of 100 mm is installed in a 250 mm pipe. Air @ atmospheric…

Q: A rectangular plate of 0.50 m x 0.50 m dimensions weighing 500 N slides down an inclined plane…

Q: Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P…

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

Q: Q2: Select one for each of the following: 1. Tire pressure affects the: a) pavement thickness b)…

A: 1. Answer:- quality of surface course (option b) Explaination:- Tire pressure affects the quality…

Q: A steel marine propeller shaft transmits a power of 5 MW at a frequency of 2.5 Hz. The diameter of…

Q: B) What is the difference between? ON na TON 5-Steady and Unsteady flow

A: Steady flow:- A steady flow can be defined as that flow in which the property of the fluid flowing…

Q: A solid 200-mm long, 40-mm diameter circular shaft has a modulus of rigidity of 70 GPa and is fixed…

Q: Why do you think having a good handwriting is important in the field of engineering?

A: Having a good handwriting is extremely imporrant in engineering as all the plans,maps,budgets made…

Q: You are estimating for a project in Melbourne CBD. Do you think site access affects the price of…

A: By way of harmless expenses, the daily operating costs will automatically rise. For instance, expect…

Q: Determine the maximum bending stress (in Pa) for the beam shown belowif P = 1670 N, T = 4684 Nm, a =…

Q: Determine the maximum axial force P that can be applied to the joint if the shear stress in each of…

A: Maximum axial force P

Q: A block of 200 kg mass rests on a rough horizontal plane. Find the force required in each of the…

Q: A V, kN 2m 3 m B kN/m

A: Please find step by step solution below:

Q: Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A…

Q: Can someone please solve this? Find load function functions and draw load effect diagrams?…

Q: An open channel is to be designed to carry 4.0m3/s at a slope of 0.005. The channel material has an…

Q: t Diagram in the shear diag

Q: A test facility setup costs 10,00,000 at the time of installation, and its scrap value is 50,000 at…

A: Given data- Initial cost= Rs 10,00,000Scrap value= Rs 50,000Useful life =10 yearsTo Find-Book value…

Q: A W530X123 is used as a fixed-ended beam with a span length of 5 m. The beam carries a uniform…

A: fy = 345 MPa = 345 N/mm2

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

Q: Required: Determine the member forces of the truss shown using the Matrix Formulation of the Method…

A: Assuming all members to be compressive in nature,

Q: The properties of the reinforced concrete beam are b = 306 mm, d = 467 mm, Ast = 1007 mm2, and Est /…

Q: 40-mm sides glass polymer fibers composite cube shown in Figure.2. The Glass polymer fibers aligned…

Q: The properties of the reinforced concrete beam are b = 309 mm, d = 476 mm, Ast = 1376 mm2, and Est /…

Concept explainers

Drainage of Pavements

Pavement Drainage holds ample significance, as it prevents the accumulation of water or any liquid on the surface of pavements and ensures proper drainage system. With proper design and gradual slopes provided, the water gets easily removed from the surface into the drains, which are essential during heavy rains and unusual weather conditions keeping it less prone to accidents and increasing the durability of the pavement structure.

Question

1. A railway embankment is made level for 180 m. the ground has a uniform slope of 1 in
12. The formation width is 9 m and the side slope is 2:1. The ground is level across the
centerline of the embankment. Determine the volume of the embankment if the high
end terminates vertically. (Take 10 intervals)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1) A rectangle ABCD, 30 m x 20m forms the plan of an excavation. AD and BC are longer sides and E is the point of intersection of the diagonals. From the original surface level and the excavated level, calculate the volume of excavation within АВCD. Pont Original level Final level A 25.590 m 22.800 m B 27.915 m 22.800 m 27.645 m 23.160 m D 25.410 m 23.160 m E 28.020 m 22.980 m Q2) Reproduced below is the page of a level book. Fill in the data. Apply usual checks. Stn. B.S I.S F.S Rise Fall R.L. Remarks 1 2.150 450.000 В.М.1 2 1.645 ? 0.500 3 2.345 4 ? 1.960 ? 2.05 1.825 0.400 7 -1.690 ? 0.120 451.730 B.M.2 Staff held against ceiling 8 ? 2.100 499.100 В.М.3
Q1) A railway embankment, 12 m wide, with side slop 11 2:1 is to be calculated for its volume of earthwork. Assuming the ground to be level in a direction transverse to be centre line, calculate the volume contained in a 180 m length the centre heights at 30 m intervals being in meters as 0.6, 1.2, 1.8, 1.5, 1.2, 0.9, 0.6 using (a) Prismoidal Rule, (b) Trapzoidal Rule or End area method, (c) comment on the obtained results and (d) compute the volume up to 150 m chainage.
5. A railway embankment 400 m long is 12 m wide at the formation level. The side slope of the embankment is 2:1. The formation level at station zero is 107.00. The embankment has a rising gradient of 1 in 100. The ground is level across the centerline. Calculate the volume of earthwork using the prismoidal rule with the following observations: Distance (m) 0 100 200 300 400 Elevation (m) 104.8 106.2 107.5 107.2 108.3
Example 4.2 Along rectangular channel is 3m wide & carries water at the rate of 13m/sec. At a certain point there is an approach change in the slope from 1:60 to 1:600 , determine: a)whether the hyd. Jump will form? Solution Q = * R2/3 * S1/2 A n 3y1 1 (3y,)(: 13 0.015 3+ 2y1 Y1 = 0.79 m 1 3y1 13 = (3y2)G 3+2y2 0.015 Y2 = 1.82m 2 (13/3) 3 3 Ye = = 1.24 m 9.81 Y1 < Yc
PROBLEM 2: Find the required slope of the channel bottom when water flowing at the rate of 5.82 m3/sec in rectangular section having a base width of 4.0 m and a depth of 2.5 m n = 0.013 а 0.00021 b. 0.00059 С. 0.00122 d. 0.00612
Plz, solve this problem, it is not graded question. ω = P = Reg# − 5180 ( kip or kN or kip/ft or kN/m) Reg # 5395
Water flows at a rate of 30m3/s in the concrete channel shown. Find the required slope of the channel. n=0.013 4m 1.6m 3.6m 2m O 1.7 0.57 0.017 O 0.0007
009 =6 Q. No 4). A rectangular channel of X ft width is supplying water at flowrate of Y ft'/s. If the slope of channel is 1/800 calculate the depth of water in the channel. Assume value of manning coefficient , n = 0.015.
An earth canal in good condition having a bottom width of 4 meters an slide slopes of 2 horizontal to 1 vertical is carrying water at a depth of 2 m. The slope of the canal is 0.0002. Determine the discharge using n = 0.020.a. 13.06 m3/sb. 12.56 m3/sc. 10.56 m3/sd. 14.89 m3/s
The open channel shown in the following figure is constructed of smooth concrete. Water flows at 3.0 m2/s in uniform flow. What is the minimum slope? Use a reasonable value of the Manning's roughness coefficlent (i.e. for smooth concrete, use n= 0.013). Given that w = 3.3 m. W. concrete channel water 60 O a. 0.00011 O b.0.00106 Oc.0.00498 O d.0.00064 O e. 0.00204
Determine the A6z = at a point 3.00 meters from the inclined lineload and 2.5 meters deep. u = 0.35 91 = 300 KN/m 92 = 500 KN/m 40 ° 6.00m 3.00 m Z = 2.50 m
Q5/A Triangular open channel. The available data are: Q = 13.5 (m³/s) v = 1 (m/s) n = 0.025 So = 0.0001 Z = 1.5 F.B = 0.8 (m) Find: Depth of water in the channel y. Width of the channel at the level of ground surface Wr.